Ryobi RY52504 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Outils Ryobi RY52504. Ryobi RY52504 User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 24
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
OPERATOR’S MANUAL
TP30 GAS PRUNER
RY52504/RY52905
SAVE THIS MANUAL FOR FUTURE REFERENCE
Your pruner has been engineered and manufactured to our high standard for dependability, ease of operation, and operator
safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.
Vue de la page 0
1 2 3 4 5 6 ... 23 24

Résumé du contenu

Page 1 - OPERATOR’S MANUAL

OPERATOR’S MANUALTP30 GAS PRUNERRY52504/RY52905SAVE THIS MANUAL FOR FUTURE REFERENCEYour pruner has been engineered and manufactured to our high stand

Page 2 - INTRODUCTION

10ASSEMBLYFILLING TANK Clean surface around fuel cap to prevent contamina-tion. Loosen fuel cap slowly. Rest the cap on a clean su

Page 3 - GENERAL SAFETY RULES

11WARNING: Do not allow familiarity with this product to make you careless. Remember that a careless fraction of a second is sufficient to inflict ser

Page 4 - SPECIFIC SAFETY RULES

12OPERATIONFig. 7CUTTING GUIDEFig. 6NOTE: For second and final cuts (from top of limb or branch), hold front cutting guide against the limb being cu

Page 5 - 50' 15m

13OPERATIONFig. 12POSITION FOR STARTINGSee Figure 9.Lay the pruner on the ground and ensure that no objects or obstructions are in the immediate vicin

Page 6

14fLATSAPPROX .050 in.Fig. 14Fig. 13WARNING:When servicing, use only identical replacement parts. Use of any other parts may create a hazard

Page 7 - FEATURES

15MAINTENANCEREPLACING THE BAR AND CHAINSee Figures 15 - 20.WARNING: To avoid possible serious injury, stop engine before re-placing the bar, chain, o

Page 8

16IDLE SPEED ADJUSTMENTSee Figure 21.If the chain turns at idle, the idle speed screw needs adjusting on the engine. Turn the idle speed screw counter

Page 9

17MAINTENANCECUTTING CORNERSIDE PLATEDEPTH GAUGETOEGULLETHEELRIVET HOLETOP PLATEPARTS Of A CUTTERFig. 24HOW TO SHARPEN THE CUTTERSSee Figures 24 - 27.

Page 10 - ASSEMBLY

18MAINTENANCECLEANING AIR FILTER SCREENSee Figure 28-29.For proper performance and long life, keep air filter clean. Remove the air filter cover by

Page 11 - OPERATION

19TROUBLESHOOTINGPROBLEM POSSIBLE CAUSE REMEDYEngine will not start. No spark. No fuel. Engine is flooded. Starter rope pulls harder now than whe

Page 12

2 Introduction ...

Page 13

20WARRANTYLIMITED WARRANTY STATEMENTTechtronic Industries North America, Inc., warrants to the original retail purchaser that this RYOBI® brand outdoo

Page 14 - MAINTENANCE

21WARRANTYTHE FOLLOWING CALIFORNIA AIR RESOURCES BOARD (CARB) STATEMENT ONLY APPLIES TO MODEL NUM-BERS REQUIRED TO MEET THE CARB REQUIREMENTS.The U.S.

Page 15

22EMISSIONS MAINTENANCE SCHEDULE AND WARRANTED PARTS LISTEmissions Parts Inspect Before Clean Every Replace Clean Every Replace Every Each U

Page 16

23NOTES

Page 17

987000-19410-18-07 (REV:01)OPERATOR’S MANUALTP30 GAS PRUNERRY52504/RY52905 WARNING:The engine exhaust from this product contains chemicals known to t

Page 18

3WARNING!Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious pers

Page 19 - TROUBLESHOOTING

4Kickback is a dangerous reaction that can lead to serious injury. Kickback may occur when the moving chain con-tacts an object at the upper portion

Page 20 - WARRANTY

5SYMBOLSSome of the following symbols may be used on this product. Please study them and learn their meaning. Proper inter-pretation of these symbols

Page 21

6SYMBOLSSERVICEServicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we su

Page 22 - 1-800-860-4050

7 FEATURESFig. 1PRODUCT SPECIFICATIONSEngine Displacement...

Page 23

8ATTACHING THE “J” HANDLESee Figure 2. Hold the top and bottom clamp snugly in position on the shaft housing so that the handle will be located to t

Page 24

9 Reinstall the bolt, lock washer, and hex nut to secure. Connect the latch on the shoulder harness to the strap hanger.ASSEMBLYCONNECTING THE P

Commentaires sur ces manuels

Pas de commentaire