Ryobi RY80533 Manuel d'utilisateur télécharger pdf (Page 17)

Page 13 — English

USING THE HIGH PRESSURE HOSE

WARNING:

Injection hazard. Fully unwrap and straighten high

pressure hose prior to and during each use and do

not allow it to become kinked. The high pressure hose

features an outer covering that provides strength to the

hose. If the outer covering becomes damaged, stop using

the hose and replace it immediately. A kinked or damaged

hose can develop a high pressure leak and result in a

possible injection or other serious personal injury.

To prevent damage to the outer covering:

 Inspect the hose before every use.

 Fully unwrap and straighten hose before use.

 Do not allow the high pressure hose to be kinked.

 Keep hose away from hot surfaces and sharp edges.

 Do not pull unit by high pressure hose.

 Do not allow hose to be crushed or wrapped around

objects.

WASHING WITH DETERGENT

See Figures 15 - 16.

As sold, this unit is designed for use with “downstream”

pressure washer detergents. To convert for use with

“upstream” detergents, contact an authorized customer

service center for more information.

NOTICE:

USE ONLY DETERGENTS DESIGNED FOR PRESSURE

WASHERS. Do not use household detergents, acids,

alkalines, bleaches, solvents, flammable material, or

industrial grade solutions, which can damage the pump

or cause property damage. Many detergents may

require mixing prior to use. Prepare cleaning solution

as instructed on the solution bottle. Always test in an

inconspicuous area before beginning.

 Remove the cap from the detergent tank and pour pressure

washer detergent in the tank. Replace cap on tank.

NOTE: The machine setting of this unit is 20:1, which

usually allows the use of 1 gallon pressure washer

detergent without further dilution. Check your detergent

instructions to be sure additional dilution is not necessary.

 Install the blue soap nozzle on the spray wand.

 Squeeze the trigger and wait approximately 5 seconds

for the detergent to appear.

Spray the detergent on a dry surface using long, even,

overlapping strokes. To prevent streaking, do not allow

detergent to dry on the surface.

Before shutting off the engine:

 Fill the detergent tank with clean water.

 Spray the clear water through the spray wand until the

tank is empty.

 If any soap remains in the spray, repeat with a second

tank of clean water.

 Shut off the engine.

NOTE: Shutting OFF ( O ) the engine will not relieve pressure

in the system. Pull trigger to release water pressure.

RINSING WITH THE PRESSURE WASHER

Turn off the pressure washer and shut off the water

supply. Pull trigger to release water pressure.

 Engage the lock out on the trigger handle by pushing up

on the lock out until it clicks into the slot.

 Remove the nozzle by placing hand over nozzle then

pulling back the quick-connect collar. Place nozzle in the

nozzle storage area on the top of the machine.

 Select the right nozzle for the job. See the chart on the

previous page for selecting the appropriate nozzle.

 Start at the top of the area to be rinsed and work down,

overlapping the strokes.

USING PUMP PROTECTOR

See Figure 17.

Regular use of a commercially available pump protector

prolongs the life of the pressure washer by removing hard

water mineral deposits, lubricating pump seals and pistons,

and preventing freeze damage. Pump protector should be

added to the unit after every use and before storage. Pump

protector can be purchased at the retailer where you purchased

your pressure washer, or by calling customer service.

The instructions below are for G-Protect Pump Protector.

For other brands, follow the instructions provided by the

manufacturer.

 Turn off the pressure washer engine and shut off the water

supply. Pull trigger to release water pressure.

 Disconnect garden hose and high pressure hose.

 Unscrew threaded top from pump protector bottle and

remove paper seal from bottle. Reinstall top on bottle and

tighten securely.

NOTE: The rubber seal should remain inside the threaded

top. If it comes out, be sure to replace before reinstalling

the top.

 Remove bottle cap and attach threaded end of bottle

securely to pressure washer pump water intake.

 Squeeze bottle to inject contents into pump.

 With engine still off, pull starter grip and rope to cycle

pump, then squeeze bottle again to guarantee complete

coverage.

 Pump is protected when the protector fluid exits the pump

outlet.

OPERATION

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 63 64

Commentaires sur ces manuels

Pas de commentaire

Ryobi RY80533 Manuel d'utilisateur Page 17

Commentaires sur ces manuels

Produits connexes et manuels pour Carwash Ryobi RY80533