Ryobi RY41130 Manuel de l'opérateur télécharger pdf (Page 11)

Page 11 — English

WARNING:

When servicing, use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes, resulting in possible

serious injury.

WARNING:

Before inspecting, cleaning, or servicing the machine,

shut off motor, wait for all moving parts to stop, and

disconnect extension cord. Failure to follow these

instructions can result in serious personal injury or

property damage.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use. Use

clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact

with plastic parts. Chemicals can damage, weaken or

destroy plastic which may result in serious personal injury.

You can often make repairs described here. For other repairs,

have the trimmer serviced by an authorized service center.

SPOOL REPLACEMENT REEL-EASY

™

BUMP

ADVANCE SYSTEM

See Figures 13 - 15.

If replacing line only, refer to the next section in this manual.

Use only 0.080 in. monofilament line.

 Stop the motor and disconnect from power supply. Hold

the string head and unscrew the spool retainer.

 Remove the empty spool from the string head.

NOTE: It is not necessary to remove the string head

housing from the drive shaft.

MAINTENANCE

 Insert the new spool into the string head.

NOTE: Make sure the arrows on the spool are aligned

with the eyelets in the string head housing. Push down

and hold the spool and housing together while completing

the installation.

 Reinstall the spool retainer to secure.

 Install line as described in the next section.

INSTALLING LINE IN REEL EASY STRING HEAD

See Figures 15 - 17.

 Stop the motor and disconnect from power supply.

 Rotate the spool clockwise as necessary to align the

arrows on the spool with the eyelets in the string head

housing.

 Cut one piece of trimmer line 10 ft. long. Insert the line

into the eyelet on the string trimmer housing. Push until

the end of the line comes out the other side of the string

head. Pull the line from the other side until equal amounts

of line appear on both sides of the spool.

 Rotate the spool clockwise to wind the line on the spool

until approximately 6 in. of line is showing on each side.

 Push the spool retainer down while pulling on line(s)

to manually advance the line and to check for proper

assembly of the string head.

INSTALLING PRO CUT II STRING HEAD

See Figure 18.

 Stop the motor and disconnect from power supply.

 Remove currently installed string head.

 Install the string head on the drive shaft until fully seated.

 Install the spool retainer and turn clockwise.

 Install line as described in the next section of this manual.

INSTALLING LINE IN PRO CUT II STRING HEAD

See Figure 19.

Use only 0.080 in. monofilament line. Use quality monofilament

replacement line for best performance.

 Stop the motor and disconnect from power supply.

 Gather two of the pre-cut lengths of trimmer line provided

or cut two pieces of trimmer line, in 11 in. lengths.

 Insert the lines into the slots located on the sides of the

string head. Line should be pushed in until approximately

1 in. protrudes from the holes on the top of the string

head.

 Remove old line by pulling it from the holes located on

the top of the string head.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 35 36

Commentaires sur ces manuels

Pas de commentaire

Ryobi RY41130 Manuel de l'opérateur Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Tondeuses à gazon Ryobi RY41130