Ryobi P111 Manuel de l'opérateur télécharger pdf (Page 5)

5 − English

ASSEMBLY

UNPACKING

This product has been shipped completely assembled.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing list

are included.

 Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

 Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-800-525-2579 for assistance.

PACKING LIST

Charger

Operator’s Manual

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Failure to heed this

warning could result in serious personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

OPERATION

WARNING:

Do not allow familiarity with products to make you

careless. Remember that a careless fraction of a second

is sufficient to inflict serious injury.

WARNING:

Always wear safety goggles or safety glasses with side

shields when operating products. Failure to do so could

result in objects being thrown into your eyes, resulting in

possible serious injury.

APPLICATIONS

You may use this product for the following purposes:

Charging Ryobi nickel-cadmium One+ 18 Volt battery

packs

CAUTION:

If at any point during the charging process none of the

LEDs are lit, remove the battery pack from the charger

to avoid damaging the product. DO NOT insert another

battery. Return the charger and battery to your nearest

service center for service or replacement.

LED FUNCTIONS OF CHARGER

See Figure 1.

 Orange LED = Charger is evaluating battery pack

 Red LED on = Battery pack is charging

CHARGING THE BATTERY PACK

Use only these Ryobi One+ 18 V battery packs with this

charger: P100 (130255004 or 130224028)

Battery packs are shipped in a low charge condition to

prevent possible problems. Therefore, you should charge

them before use.

If the charger does not charge the battery pack under normal

circumstances, return both the battery pack and charger

to your nearest Authorized Service Center for electrical

check.

CHARGING A COOL BATTERY PACK

 Connect the charger to the power supply. Make sure the

power supply is normal household voltage, 120 Volts, AC

only, 60 Hz.

Place the battery pack on a stable surface. Place the

charger over the battery stem.

 Press down on the charger to be sure contacts on

the battery pack engage properly with contacts in the

charger.

 The charge indicator light (LED) will light up red and glow

when the charger is properly connected to power supply.

This light indicates the charger is operating properly. It

will remain on until battery pack is removed from charging

stand or charger is disconnected from power supply.

 If both red and orange LED indicators glow, the battery

pack is deeply or completely discharged, and 10-12 hours

or longer of charging time is required to fully recharge

battery pack.

 The battery pack will become slightly warm to the

touch while charging. This is normal and does not

indicate a problem.

 Do not place the charger and battery pack in an area of

extreme heat or cold. They will work best at normal room

temperature.

NOTE: The charger and battery pack should be placed

in a location where the temperature is more than 50°F

but less than 100°F.

When batteries become fully charged, unplug the charger

from the power supply and remove the charger.

1 2 3 4 5 6 7 8 9 10 ... 19 20

Commentaires sur ces manuels

Pas de commentaire

Ryobi P111 Manuel de l'opérateur Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Chargeurs de batterie Ryobi P111