Ryobi BE318-2 Manuel de l'opérateur télécharger pdf (Page 8)

8 - English

OPERATION

WARNING:

Do not allow familiarity with tools to make you care-

less. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes resulting in possible

serious injury.

WARNING:

Do not use any attachments or accessories not

recommended by the manufacturer of this tool. The use

of attachments or accessories not recommended can

result in serious personal injury.

APPLICATIONS

You may use this tool for the purposes listed below:

Sanding wood, metals, plastics, and other materials

Smoothing rough boards, chamfering, rounding edges

Removing rust, paint, varnishes, and stains

SELECTING SANDING BELTS

Selecting the correct size and type of sanding belt is an

important step in achieving a high quality sanded finish. Alu-

minum oxide, silicon carbide, and other synthetic abrasives

are best for power sanding.

In general, when sanding, coarse grit removes the most

material and fine grit produces the best finish. The condi-

tion of the surface to be sanded determines which grit will

do the best job. If the surface is rough, start with a coarse

grit and sand until the surface is uniform. Then use medium

grit to remove scratches left by the coarser grit. Finally, use

finer grit for finishing the surface. Always continue sanding

with each grit until the surface is uniform.

USING SANDING BELTS

TO INSTALL/CHANGE SANDING BELTS

See Figures 2 - 4, page 13.

Follow these steps to install or change sanding belts.

 Unplug the sander.

WARNING:

Failure to unplug the tool could result in serious injury

due to accidental starting.

 Position the sander on its side with the cord on the left.

WARNING:

Keep hands and fingers clear of both rollers and spring

mechanism at all times. Failure to do so could result in

fingers getting pinched, causing serious injury.

 Raise the tension release lever.

NOTE: If you are changing sanding belts, remove the old

sanding belt at this time.

 Install the sanding belt.

CAUTION:

If the sanding belt is not a bidirectional belt, ensure that

the arrow inside the belt is pointing in the direction of the

rotation (clockwise when looking into the open side of the

sander). Installing unidirectional sanding belts backwards

can create a hazardous condition.

 Align the sanding belt to its correct position.

 Lower the tension release lever to secure the sanding

belt.

TO ADJUST SANDING BELT TRACKING

See Figures 5 - 6, page 13.

Belt life is greatly increased if you regularly adjust the sand-

ing belt tracking. When correctly adjusted, the outer edge

of the sanding belt should be even with the outer edge of

the base of the sander.

When you install a new sanding belt, you may need to

adjust the sanding belt tracking several times until the belt

becomes conditioned.

Follow these steps to adjust sanding belt tracking.

WARNING:

Before connecting the sander to a power supply, always

make sure it is not in the “locked-on” position. Failure

to do so could result in accidental starting of the sander

resulting in possible serious injury.

 Connect the sander to a power supply.

 Position the sander upside down with the cord on the

left.

NOTE: This position is for adjustments only. The sanding

belt should not contact a workpiece or any foreign object

when you are making belt tracking adjustments.

 Depress the switch trigger and release immediately.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 35 36

Commentaires sur ces manuels

Pas de commentaire

Ryobi BE318-2 Manuel de l'opérateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Ponceuses électriques Ryobi BE318-2