Ryobi BS903 Manuel d'utilisateur télécharger pdf (Page 9)

9 — English

ASSEMBLY

UNPACKING

This product requires assembly.

 Carefully remove the tool and any accessories from the

box. Place it on a level work surface.

NOTE: This tool is heavy. To avoid back injury, lift with

your legs, not your back, and get help when needed.

 Inspect the tool carefully to make sure no breakage or

damage occurred during shipping.

 Do not discard the packing material until you have carefully

inspected and satisfactorily operated the tool.

 If any parts are damaged or missing, please call

1-800-525-2579 for assistance.

WARNING:

If any parts are damaged or missing, do not operate this

tool until the missing parts are replaced. Failure to do so

could result in possible serious personal injury.

WARNING:

Do not attempt to modify this tool or create accessories

not recommended for use with this tool. Any such

alteration or modiﬁcation is misuse and could result in a

hazardous condition leading to possible serious personal

injury.

WARNING:

Do not connect to power supply until assembly is

complete. Failure to comply could result in accidental

starting and possible serious personal injury.

MOUNTING BAND SAW TO WORKBENCH

If the band saw is to be used in a permanent location, we

recommend that you secure it to a workbench or other

stable surface. When mounting the saw to a workbench,

holes should be drilled through the supporting surface of

the workbench.

 Each hole in the saw base should be bolted securely

using bolts, lock washers, and hex nuts (not included).

 Place band saw on the workbench. Using the saw base

as a pattern, locate and mark the holes where the band

saw is to be mounted.

 Drill holes through the workbench.

 Place band saw on the workbench aligning holes in the

saw base with the holes drilled in the workbench.

 Insert bolts (not included) and tighten securely with lock

washers and hex nuts (not included).

NOTE: All bolts should be inserted from the top. Install

the lock washers and hex nuts from the underside of the

bench.

Supporting surface where band saw is mounted should be

examined carefully after mounting to insure that no movement

during use can result. If any tipping or walking is noted,

secure workbench or support surface before beginning

cutting operation.

CLAMPING BAND SAW TO WORKBENCH

See Figure 5, page 18.

If the band saw is to be used as a portable tool, it is

recommended that you fasten it permanently to a mounting

board that can easily be clamped to a workbench or other

supporting surface. The mounting board should be of

sufﬁcient size to avoid tipping of saw while in use. Any

good grade plywood or chipboard with a 3/4 in. thickness

is recommended.

 Mount saw to board using holes in saw base as a template

for hole pattern. Locate and mark the holes where the

band saw is to be mounted.

 Follow the last three steps in the section Mounting Band

Saw to Workbench, shown above.

If lag bolts are used, make sure they are long enough to

go through holes in the saw base and material the saw is

being mounted to. If machine bolts are being used, make

sure bolts are long enough to go through holes in the saw

base, the material being mounted to, and the lock washers

and hex nuts.

NOTE: It may be necessary to countersink hex nuts and

washers on bottom side of mounting board.

MOUNTING THE SAW TABLE

See Figures 6 - 7, pages 18 - 19.

 Loosen and remove the table aligning bolt, washer, and

wing nut on the saw table.

 Loosen the table extension knobs beneath the sliding

table extension by turning them clockwise.

 Slide the table extension out and retighten the table

extension knobs.

 Standing at the front of the band saw, slide the saw table

past the blade and through the slot moving from the right

side of the saw table to the left.

 Align the screw holes in the saw table with the holes in

the saw table bracket.

 Using the phillips screws, attach the saw table to the saw

table bracket. Tighten phillips screws securely.

 Close the sliding table extension, retighten the table

extension knobs, then attach the table aligning bolt,

washer, and wing nut to the saw table.

NOTE: The wing nut goes below the saw table.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 55 56

Commentaires sur ces manuels

Pas de commentaire

Ryobi BS903 Manuel d'utilisateur Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Scies à moteur Ryobi BS903