Ryobi P503 Manuel d'utilisateur télécharger pdf (Page 9)

9 - English

WARNING:

Do not allow familiarity with products to make you care-

less. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes resulting in possible

serious injury.

WARNING:

Do not use any attachments or accessories not recom-

mended by the manufacturer of this product. The use of

attachments or accessories not recommended can result

in serious personal injury.

APPLICATIONS

You may use this product for the purposes listed below:

Cutting all types of wood products (lumber, plywood,

paneling, composition board, and hard wood)

This product will accept Ryobi One+ 18 V lithium-ion battery

packs and Ryobi One+ 18 V nickel-cadmium battery packs.

Both types of battery packs are shown on this page. Following

pages will show the lithium-ion 18 V battery pack.

For complete charging instructions, refer to the Operator’s

Manual for the battery packs and chargers listed in the

General Safety Rules.

BATTERY PROTECTION FEATURES

Ryobi lithium-ion batteries are designed with features that

protect the lithium-ion cells and maximize battery life.

If the tool stops during use, release the trigger to reset and

resume operation. If the tool still does not work, the battery

needs to be recharged.

INSTALLING THE BATTERY PACK

See Figure 4, page 15.

NOTE: The battery pack is shipped in a low charge condi-

tion. Therefore, it must be charged prior to use. Refer to

CHARGING BATTERY PACK for charging instructions.

 Place the battery pack in the saw. Align the raised rib

on the battery pack with the groove inside the saw, then

slide the battery pack into the saw.

 Make sure the latches on each side of your battery pack

snap into place and the battery pack is secured in the

saw before beginning operation.

OPERATION

CAUTION:

When placing battery pack in the tool, be sure raised

rib on battery pack aligns with the bottom of the tool

and latches into place properly. Improper installa-

tion of the battery pack can cause damage to internal

components.

REMOVING THE BATTERY PACK

See Figure 4, page 15.

 Locate the latches on the side of the battery pack and

depress them to release the battery pack from the saw.

 Remove battery pack from the saw.

WARNING:

Battery tools are always in operating condition. There-

fore, switch should always be locked when not in use or

carrying at your side.

KICKBACK

See Figures 5 - 8, pages 15 and 16.

Kickback occurs when the blade stalls rapidly and the saw

is driven back towards you. Blade stalling is caused by any

action which pinches the blade in the wood.

DANGER:

Release switch immediately if blade binds or saw stalls.

Kickback could cause you to lose control of the saw. Loss

of control can lead to serious injury.

To guard against kickback, avoid dangerous practices such

as the following.

Setting blade depth incorrectly.

Sawing into knots or nails in workpiece.

Twisting the blade while making a cut.

Making a cut with a dull, gummed up, or improperly set

blade.

Supporting the workpiece incorrectly.

Forcing a cut.

Cutting warped or wet lumber.

Operating the tool incorrectly or misusing the tool.

To lessen the chance of kickback, follow these safety prac-

tices.

Keep the blade at the correct depth setting. The depth

setting should not exceed 1/4 in. below the material being

cut.

Inspect the workpiece for knots or nails before cutting.

Never saw into a knot or nail.

Make straight cuts. Always use a straight edge guide

when rip cutting. This helps prevent twisting the blade.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 43 44

Commentaires sur ces manuels

Pas de commentaire

Ryobi P503 Manuel d'utilisateur Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Scies à moteur Ryobi P503