Ryobi MT100 Manuel de l'opérateur télécharger pdf (Page 9)

9 - English

OPERATION

WARNING:

Do not allow familiarity with products to make you care-

less. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes resulting in possible

serious injury.

WARNING:

Do not use any attachments or accessories not recom-

mended by the manufacturer of this product. The use of

attachments or accessories not recommended can result

in serious personal injury.

APPLICATIONS

You may use this product for the purposes listed below:

Straight cutting in wood, plastic, and thin metals

Flush cutting in wood and drywall

Sanding in corners and other hard-to-reach areas

Scraping paint, varnish, and adhesive backed coverings

from surfaces.

INSTALLING ACCESSORIES

See Figures 2, page 12.

 Unplug the multi-tool.

 Using the hex key provided, rotate the screw counter-

clockwise. Remove the screw and washer assembly and

set aside.

 Place the desired accessory on the multi-tool head so that

the openings on the accessory fit on the raised parts of

the head. Reinstall the screw and washer assembly then

tighten securely.

NOTE: Some accessories will not fit directly onto the

multi-tool head. To use these accessories, first install

the adaptor and then install the accessory as described

above.

REMOVING ACCESSORIES

See Figure 2, page 12.

 Unplug the multi-tool.

 Remove the screw and washer assembly.

 Remove the accessory.

TURNING THE MULTI-TOOL ON/OFF

See Figure 3, page 12.

 To turn the tool ON: push the ON/OFF switch to the ON

( I ) position.

 To turn the tool OFF: push the ON/OFF switch to the OFF

( O ) position.

SELECTING THE RIGHT SPEED

See Figures 4 - 5, pages 12 and 13

The multi-tool has a speed range of 10,000 - 20,000

oscillations per minute. To select the right speed for each

job, use a practice piece of material. Vary speed to find the

best speed for the accessory you are using and the job to

be done.

Use the indicator mark above the speed control dial to set

the best speed for the job. The speed control dial has six

settings (1, 2, 3, 4, 5, and 6). For example, a speed setting

of 1 is approximately 10,000 to 11,000 OPM, and a speed

setting of 6 is approximately 19,000 to 20,000 OPM.

Refer to the Speed Dial Settings table, to determine the

proper speed based on the material being worked and the

type of accessory being used.

SLOWER SPEEDS

See Figure 5, page 13

Certain materials, some plastics for example, require a

relatively slow speed because the friction of the tool generates

heat and causes the plastic to melt at high speed.

To determine the optimum operational speed for different

materials and accessories, refer to the Speed Dial Settings

table. Look this table over and become familiar with it.

The best way to determine the correct speed for work on

any material is to practice for a few minutes on a piece of

scrap, even after referring to the table. You can quickly

learn that a slower or faster speed is more effective just by

observing what happens when you make a pass or two at

different speeds.

When working with a scrap piece of plastic, start at a slow

rate of speed and increase the speed until you observe

whether the plastic is melting at the point of contact; reduce

the speed slightly to get optimum working speed without

melting the workpiece.

NOTE:

Plastic and materials that could melt at low temperatures

should be cut at low speeds.

Soft wood should be cut at high speed.

Aluminum, tin, copper, lead, and zinc alloys may be cut at

any speed, depending on the type of cutting being done.

Use paraffin or other suitable lubricant on the cutter to

prevent the cut material from adhering to the cutter teeth.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 35 36

Commentaires sur ces manuels

Pas de commentaire

Ryobi MT100 Manuel de l'opérateur Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Ryobi MT100