Ryobi P202B Manuel d'utilisateur télécharger pdf (Page 8)

8 – English

OPERATION

TO REMOVE BATTERY PACK

 Depress the latches on each side of the battery pack.

 Remove the battery pack from the drill.

WARNING:

Battery products are always in operating condition.

Therefore, the switch should always be locked when not

in use or carrying at your side.

SWITCH TRIGGER

See Figure 3, page 11.

To turn the drill ON, depress the switch trigger. To turn it

OFF, release the switch trigger.

VARIABLE SPEED

The variable speed switch trigger delivers higher speed with

increased trigger pressure and lower speed with decreased

trigger pressure.

NOTE: You might hear a whistling or ringing noise from the

switch during use. Do not be concerned; this is a normal

part of the switch function.

DIRECTION OF ROTATION SELECTOR

(FORWARD/REVERSE/CENTER LOCK)

See Figure 3, page 11.

The direction of bit rotation is reversible and is controlled

by a selector located above the switch trigger. With the drill

held in normal operating position, the direction of rotation

selector should be positioned to the left of the switch trigger

for forward drilling. The drilling direction is reversed when

the selector is to the right of the switch trigger.

Setting the switch trigger in the OFF (center lock) position

helps reduce the possibility of accidental starting when not

in use.

CAUTION:

To prevent gear damage, always allow the chuck to

come to a complete stop before changing the direction

of rotation.

To stop the drill, release the switch trigger and allow the

chuck to come to a complete stop.

NOTE: The drill will not run unless the direction of rotation

selector is pushed fully to the left or right.

Avoid running the drill at low speeds for extended periods

of time. Running at low speeds under constant usage may

cause the drill to become overheated. If this occurs, cool the

drill by running it without a load and at full speed.

KEYLESS CHUCK

See Figure 4, page 11.

The drill has a keyless chuck to tighten or release drill bits

in the chuck jaws. The arrows on the chuck indicate which

direction to rotate the chuck body in order to LOCK (tighten)

or UNLOCK (release) the drill bit.

WARNING:

Do not hold the chuck with one hand and use the power

of the drill to tighten the chuck jaws on the drill bit. The

chuck body could slip in your hand, or your hand could

slip and come in contact with the rotating drill bit. This

could cause an accident resulting in serious personal

injury.

TWO-SPEED GEAR TRAIN (HI-LO)

See Figure 5, page 11.

The drill has a two-speed gear train designed for drilling or

driving at LO (1) or HI (2) speeds. A slide switch is located on

top of the drill to select either LO (1) or HI (2) speed. When

using drill in the LO (1) speed range, speed will decrease

and unit will have more power and torque. When using drill

in the HI (2) speed range, speed will increase and unit will

have less power and torque. Use LO (1) speed for high power

and torque applications and HI (2) speed for fast drilling or

driving applications.

ADJUSTABLE TORQUE CLUTCH

This product is equipped with an adjustable torque clutch

for driving different types of screws into different materials.

The proper setting depends on the type of material and the

size of screw you are using.

ADJUSTING TORQUE

See Figure 6, page 11.

There are twenty-four torque indicator settings located on

the front of the drill.

 Rotate the adjusting ring to the desired setting.

• 1-4 Fordrivingsmallscrews

• 5-8 Fordrivingscrewsintosoftmaterial

• 9-12 Fordrivingscrewsintosoftandhard 

materials

• 13-16 Fordrivingscrewsintohardwood

• 17-20 Fordrivinglargescrews

• 21-

For heavy drilling

BIT STORAGE

See Figure 7, page 12.

When not in use, bits provided with the drill can be placed

in the storage area located on the base of the drill.

MAG TRAY

™

(SCREW HOLDER)

See Figure 7, page 12.

The magnetic tray conveniently stores screws or other small

parts.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Ryobi P202B Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Ryobi P202B