Ryobi ZRCSB133L Manuel d'utilisation et d'entretien télécharger pdf (Page 12)

12 - English

OPERATION

WARNING:

Never tie the lower blade guard in a raised position.

Leaving the blade exposed could lead to serious injury.

CAUTION:

Never use saw when guard is not operating correctly.

Check the guard for correct operation before each use.

The guard is operating correctly when it moves freely and

readily returns to the closed position. If you drop the saw,

check the lower blade guard and bumper for damage at

all depth settings before reuse.

If at any time the lower blade guard does not snap closed,

unplug the saw from the power supply. Exercise the lower

guard by moving it rapidly back and forth from the full open

position to the closed position several times. Normally this

will restore the guard to its normal operating condition. If

it does not correct a slow or sluggish closing lower guard,

do not use the saw. Take it to an authorized factory service

center for repair.

STARTING/STOPPING THE SAW

See Figure 10, page 18.

To start the saw: Depress the switch trigger.

Always let the blade reach full speed, then guide the saw

into the workpiece.

WARNING:

The blade coming in contact with the workpiece before

it reaches full speed could cause the saw to “kickback”

towards you resulting in serious injury.

To stop the saw: Release the switch trigger.

After you release the switch trigger, allow the blade to come

to a complete stop. Do not remove the saw from the

workpiece while the blade is moving.

ADJUSTING BLADE DEPTH

See Figure 11, page 18.

Always keep correct blade depth setting. Less than a full tooth

of the blade teeth should be visible below the workpiece.

More blade depth will increase the chance of kickback and

cause the cut to be rough. For more depth of cut accuracy,

a scale is located on the upper blade guard.

To adjust the blade depth:

Unplug the saw.

Loosen depth adjustment knob on back of saw.

Determine the desired depth of cut.

Locate depth of cut scale on back of upper blade guard.

Hold base flat against the workpiece and raise or lower

saw until the index point (or reference mark) on bracket

aligns with notch on blade guard.

Tighten depth adjustment knob securely.

USING THE LASER GUIDE

See Figure 12, page 18.

WARNING:

Do not stare into the laser beam or turn the laser on when

the tool is not in use. Failure to heed this warning could

result in possible serious personal injury.

The laser guide will generate a red laser beam on the work

surface in front of the saw when turned on. The laser aids in

following the line of cut when cutting the workpiece.

NOTE: The laser unit comes from the factory already installed

and aligned. If the laser becomes misaligned after time, refer

to the Adjustments section later in this manual.

 Unplug the saw.

 Mark the line to be cut on the workpiece.

 Adjust the depth and angle of the cut as needed.

 Plug the tool into a power supply and press the laser guide

button to activate the laser.

 Start the motor.

NOTE: Do not touch the blade to the workpiece until the

saw has reached maximum speed.

 Slowly push the saw forward into the workpiece.

NOTE: Keep the laser beam on the marked line on the

workpiece for precision cutting.

 Once the cut is complete, allow the saw to come to a

complete stop before turning off the laser.

OPERATING THE SAW

See Figures 13 - 15, page 19.

It is important to understand the correct method for operat-

ing the saw. Refer to the figures in this section to learn the

correct and incorrect ways for handling the saw.

WARNING:

To make sawing easier and safer, always maintain proper

control of the saw. Loss of control could cause an ac-

cident resulting in possible serious injury.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 51 52

Commentaires sur ces manuels

Pas de commentaire

Ryobi ZRCSB133L Manuel d'utilisation et d'entretien Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Ryobi ZRCSB133L