Ryobi r163 Manuel d'utilisateur télécharger pdf (Page 7)

7 − English

OPERATION

 Loosen the lock lever on the base.

NOTE: It should not be possible to move the router

motor with the lock lever tightened and the motor cor-

rectly installed in either base. If movement is possible

with the lock lever tightened in either of the bases, an

adjustment to the lock lever needs to be made. See

Adjustments.

 Hold the handles and pull the adjustment bar from the

slot in the motor base.

 Lift the base up from the slot until the adjustment bar tab

passes out of the slot area.

 After the tab has cleared the slot, release the adjustment

bar and press the spindle lock down and in (until it fully

locks in the collet spindle) so that it slides behind the

base housing.

NOTE: When using the spindle lock for any applica-

tion, make sure that the latch goes all the way in. If the

latch is depressed and does not go all the way in, turn

the collet with the wrench provided until the spindle lock

locks into place.

Pull the base until it dislodges from the motor. Use cau-

tion, as forcing may result in permanent damage to the

locking mechanism.

To install the base:

 Unplug the router.

 With the base right side up, loosen the lock lever.

 Push the spindle lock in, holding it into place.

 Align arrow on base with arrow on motor.

 Push the base until it lodges into the motor housing. The

spindle lock can be released once the motor slides down

into the base. It will disengage once it has cleared the

inside of the base. Use caution as forcing may result in

permanent damage to the locking mechanism.

 Pull the adjustment bar.

 Place the adjustment bar tab in the slot on the motor.

 Tighten the lock lever.

WARNING:

If the collet nut is not securely tightened, the bit may

detach during use, causing serious personal injury.

WARNING:

Never use bits which are larger in diameter than the open-

ing in the router subbase. These situations could cause

possible loss of control or create other hazardous condi-

tions that could cause possible serious personal injury.

NOTICE:

To prevent damage to the spindle or spindle lock, always

allow motor to come to a complete stop before engaging

the spindle lock.

WARNING:

If you are changing a bit immediately after use, be careful

not to touch the collet nut, bit, or collet with your hands or

fingers. You will get burned because of the heat buildup

from cutting. Always use the wrench provided.

WARNING:

Bit continues to rotate after the router has been turned off.

To avoid injury, wait until the bit has come to a complete

stop before removing router from the workpiece.

INSTALLING/REMOVING BITS

See Figure 2, page 14.

 Unplug the router.

To install the bit:

Push the spindle lock down and in, holding it into place.

Loosen the collet nut and remove the bit.

Insert the bit until it is approximately 1/8 in. to 1/4 in. away

from the collet nut face.

NOTE: Make sure that the collet always clamps the shank

(non-cutting end) of the bit.

Tighten the collet nut securely by turning it clockwise with

the wrench provided.

Release the spindle lock.

To remove the bit:

Push the spindle lock down and in, holding it into place.

Loosen the collet nut and remove the bit.

Release the spindle lock.

LED WORKLIGHT

See Figure 3, page 14.

The two LED worklights on the base of the router motor will

come on when the on/off switch is in the ON ( I ) position. This

provides additional lighting on the surface of the workpiece

for operation in lower-light areas.

1 2 3 4 5 6 7 8 9 10 11 12 ... 39 40

Commentaires sur ces manuels

Pas de commentaire

Ryobi r163 Manuel d'utilisateur Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Routeurs Ryobi r163