Ryobi RAP200 Manuel d'utilisateur télécharger pdf (Page 11)

11 — English

WARNING:

To reduce the risk of fire or explosion: Do not use with

flammable liquids (i.e., paint stripper, paint remover,

brush cleaner, mineral spirits, lacquer thinner, turpentine,

acetone, gasoline, kerosene, etc.). Use only water (for

water based paints) or Klean Strip® Revolutionary White

Formula Paint Thinner (for oil-based paints or varnish).

OVERNIGHT STORAGE (UP TO 12 HOURS)

NOTE: These instructions are for latex paint and water based

materials only. If you are using oil-based material, refer to

Cleaning the Paint Station and Long Term Storage for

instructions. Stains and oil based materials do not keep for

any extended period of time.

 Lock pistol-grip sprayer and follow Release Pressure

Procedure.

 Turn ON/OFF switch OFF.

Unplug the paint station.

 Leave intake tube and return tube in paint.

 Gently pour 1/2 cup water over top of paint to prevent

drying.

 Close lid on 3.5 gallon container. Wrap damp cloth around

tubes and over opening of container. If using 5 gallon or

other container, wrap tubes and container with plastic

to seal out air.

 Wrap pistol-grip sprayer with damp cloth and place in

plastic bag. Seal bag.

 Store for short time out of sunlight. For longer storage,

follow instructions for Cleaning the Piant Station.

CLEANING THE PAINT STATION

See Figures 18-19, page 18.

The solution used to clean the sprayer is determined by the

type of material that has been sprayed. For anything other

than latex material use Klean Strip® Revolutionary White

Formula Paint Thinner (for oil-based paints or varnish).

CAUTION:

It is important to thoroughly clean paint station and

pistol-grip sprayer after each use or when changing paint

color. Allowing paint or stain to remain in an idle tool for

an extended period of time can cause its hoses to clog

and its moving parts to seize.

 Always use drop cloths or other cover to protect areas

from possible spills.

 Lock pistol-grip sprayer and follow Release Pressure

Procedure.

Unplug the paint station.

Remove the spray tip and nozzle tip guard from

sprayer.

not hold the sprayer at an angle. This will result in

uneven coverage.

• Depress the trigger to start the spray at the beginning

of the stroke and release the trigger as you end the

stroke. To prevent material build-up, do not keep the

trigger depressed as you proceed to the next stroke.

• Make one pass for each stroke. Overlap strokes in

halves for full coverage.

When finished, return any unused paint or stain to its

original container and thoroughly clean the sprayer.

PAINTING WITH THE ROLLER ATTACHMENT

See Figures 16-17, pages 17 - 18.

NOTE: The pistol-grip sprayer is used to control the flow of

paint into the roller attachment. Pull the trigger only when

more paint is needed on the roller.

Turn lock-off thumbscrew counterclockwise to lock pistol-

grip sprayer trigger.

 Turn off paint station and release pressure from spraying.

 Assemble the 9 in. roller into the roller head according to

the Installing Paint Roller.

Remove nozzle tip guard and spray tip from pistol-grip

sprayer.

 Thread roller handle onto sprayer (make sure rubber

washer is in the roller handle before assembling).

 Tighten securely with an adjustable wrench.

Snap roller head onto roller handle (make sure latches

are completely engaged).

 Turn ON/OFF switch ON.

 Turn HIGH/LOW pressure control to ROLLING icon (LOW

pressure).

 Turn prime/spray lever to SPRAY.

Squeeze the trigger. Once the roller has paint, release

the trigger and squeeze again only when more paint is

needed.

NOTE: Do not continuously squeeze the trigger. For best

results, after every third stroke, pull trigger for 1 second,

release, then continue to paint.

To create an even coating over the entire surface:

 • Apply paint or stain in an area several feet wide in a

zig-zag direction.

 • Roll back and forth repeatedly over the same area

until the entire area is covered and the roller marks

are smoothed out.

 • If additional coats are necessary, let paint or stain dry

completely between coats.

When finished, lock pistol-grip sprayer trigger and follow

Release Pressure Procedure.

Unplug the paint station.

OPERATION

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 47 48

Commentaires sur ces manuels

Pas de commentaire

Ryobi RAP200 Manuel d'utilisateur Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Ryobi RAP200