Ryobi RY28060 Manuel de l'opérateur télécharger pdf (Page 15)

11 — English

NOTE: The line trimming cut-off blade on the grass deflector

will cut the line to the correct length.

NOTE: If the line is worn too short you may not be able to

advance the line by tapping it on the ground. If so, stop the

engine and manually advance the line.

To advance the cutting line manually:

Stop the engine and disconnect the spark plug wire.



Push the knob in while pulling on line(s) to manually

advance the line.

NOTE: Dual Spool

™

Fixed Line Adaptor line cannot be

advanced. To replace the line, refer to Installing Line in

Dual Spool

™

Fixed Line String Head Insert later in this

manual.

CUTTING TIPS

See Figures 16.

 Avoid hot surfaces by always keeping the tool away from

your body. (Proper operating position shown in figure 15.)

 Keep the trimmer tilted toward the area being cut; this is

the best cutting area.

 The curved shaft trimmer cuts when passing the unit from

right to left. The straight shaft trimmer cuts when passing

the unit from left to right. This will avoid throwing debris at

the operator. Avoid cutting in the dangerous area shown

in illustration.

 Use the tip of line to do the cutting; do not force string

head into uncut grass.

 Wire and picket fences cause extra line wear, even

breakage. Stone and brick walls, curbs, and wood may

wear line rapidly.

 Avoid trees and shrubs. Tree bark, wood moldings, siding,

and fence posts can easily be damaged by the line.

GRASS DEFLECTOR LINE TRIMMING CUT-OFF

BLADE

See Figure 17.

The trimmer is equipped with a line trimming cut-off blade

on the grass deflector. For best cutting, advance line until it

is trimmed to length by the cut-off blade. Advance the line

whenever you hear the engine running faster than normal,

OPERATION

or when trimming efficiency diminishes. This will maintain

best performance and keep the line long enough to advance

properly.

STARTING AND STOPPING

See Figures 18 - 20.

Brushcutter should be on a flat, bare surface for starting.

To start a cold engine:

Slowly press the primer bulb 10 times.

NOTE: After the 7th press, fuel should be visible in the

primer bulb. If it is not, continue to press the primer until

you see fuel in the bulb.

Set the choke lever to the FULL CHOKE position.

Squeeze the throttle trigger fully and pull starter handle

sharply until engine attempts to run. Do not pull the starter

handle more than four (4) times.

NOTE: Keep throttle trigger squeezed fully.

Set the choke lever to the HALF CHOKE position.

Pull the starter grip until the engine runs. Do not pull the

starter grip more than six (6) times.

NOTE: If the engine does not start, return to the full choke

position and repeat the steps that follow.

Allow the engine to run for 10 seconds, then set the choke

lever to the RUN position.

To restart a warm engine:

Slowly press the primer bulb 10 times.

Set the choke lever to the RUN position.

Squeeze the throttle trigger fully and pull the starter handle

until the engine runs.

To stop the engine:



To stop the engine, release the throttle trigger and depress

the STOP switch to the stop position “ ”.

IF ASSISTANCE IS REQUIRED FOR THIS PRODUCT:

Do not return this product to the retail store where it was

purchased. Please call our Customer Service Department

for any issues you may have.

For Help Call: 1-800-860-4050

MAINTENANCE

WARNING:

When servicing, use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 51 52

Commentaires sur ces manuels

Pas de commentaire

Ryobi RY28060 Manuel de l'opérateur Page 15

Commentaires sur ces manuels

Produits connexes et manuels pour Tondeuses à gazon Ryobi RY28060