Ryobi RLM1956MEB Manuel de l'opérateur télécharger pdf (Page 10)

English

chipped, spark plug should be replaced.

NOTE: If replacing, use the following recommended

plugs are Torch E7RTC and NGK BPR6HS.

5. Measure plug gap. The correct gap is 0.71 mm -

0.79 mm. To widen gap, if necessary, carefully bend

the ground (top) electrode. To lessen gap, gently tap

ground electrode on a hard surface.

6. Seat spark plug in position; thread in by hand to prevent

cross-threading.

7. Tighten with wrench to compress washer. If spark plug

is new, use 1/2 turn to compress washer appropriate

amount. If reusing old spark plug, use 1/8 to 1/4 turn for

proper washer compression.

NOTE: An improperly tightened spark plug will become

very hot and could damage the engine.

8. Reinstall spark plug boot.

REPLACING THE WHEELS

See figure 11.

WARNING

Only use replacement wheels approved by the

manufacturer of your mower. Using wheels not approved

by the manufacturer of your mower is hazardous and

could result in serious personal injury.

1. Stop the engine and disconnect the spark plug wire.

Allow blade to come to a complete stop.

2. Remove the hub cap.

3. Remove the nut from the wheel axle, then remove the

wheel.

4. Replace with new wheel and reinstall nut to secure.

STORING THE PRODUCT

When storing the mower for 30 days or more:

■ If using fuel stabilizer, follow stabilizer manufacturer’s

directions to add stabilizer to petrol in fuel tank. Run

engine at least 10 minutes after adding stabilizer to

allow the stabilizer to reach the carburetor.

WARNING

Do not store the lawn mower with petrol in the tank

inside a building where fumes may reach an open ame

or spark.

■ If not using fuel stabilizer, allow the engine to run until

the mower is completely out of petrol.

■ Once the engine has stopped, allow the blade to come

to a complete stop and disconnect the spark plug wire.

■ Turn the fuel valve to the closed position.

■ Turn mower on its side (with carburetor facing up) and

clean grass clippings that have accumulated on the

underside of the mower deck.

■ Clean the underside of the mower deck.

■ Wipe the mower clean with a dry cloth.

■ Check all nuts, bolts, knobs, screws, fasteners, etc., for

tightness.

■ Inspect moving parts for damage, breakage, and wear.

Have repairs made on any damaged or missing parts.

■ Store the mower in a well-ventilated area that is clean,

dry, and out of the reach of children.

■ Do not store near corrosive materials such as fertilizer

or rock salt.

To lower the handle before storing:

See figure 12.

■ Loosen the starter rope guide knob. Remove starter

rope from guide and allow to retract into engine.

■ Fully loosen the handle knobs on the sides of the

handle and fold the upper handle down.

■ Push inward on each side of the lower handle, and

lift the sides of the lower handle past the edges of the

handle mounting brackets.

■ Fold the lower handle forward, making sure not to bend

or kink the control cables.

TRANSPORTATION

■ Stop the machine, disconnect the spark plug wire and

wait until the blade comes to a complete stop, and allow

it to cool.

■ Empty the fuel tank by running the engine till it stops.

Empty oil by following instruction for changing oil.

■ Secure the machine against movement or falling to

prevent injury to persons or damage to the machine.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 19 20

Commentaires sur ces manuels

Pas de commentaire

Ryobi RLM1956MEB Manuel de l'opérateur Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Tondeuses à gazon Ryobi RLM1956MEB