Ryobi BE319 Manuel d'utilisateur télécharger pdf (Page 8)

8 - English

OPERATION

WARNING:

Collected sanding dust from sanding surface coatings

such as polyurethanes, linseed oil, etc., can self-ignite in

the sander dust collection bag or elsewhere and cause

fire. To reduce the risk of fire, always empty the dust

bag frequently (10-15 minutes) while sanding and never

store or leave a sander without totally emptying its dust

bag. Also follow the recommendations of the coatings

manufacturers.

Follow these steps to empty the dust collection bag.

 Unplug the sander.

 Remove the dust collection bag from the sander.

 Unzip the dust bag.

 Shake out the dust.

 Zip up the dust bag.

 Replace the dust collection bag.

NOTE: Periodically, you should turn the dust bag

inside-out and thoroughly clean it.

TURNING THE SANDER ON/OFF

See Figure 7, page 12.

 To turn on the sander: Depress the switch trigger.

 To turn off the sander: Release the switch trigger.

LOCKING ON THE SANDER

See Figure 7, page 12.

The lock-on feature allows you to lock the switch trigger in

the ON position. Locking the switch trigger on allows you to

operate the sander for extended periods of time.

If you have the lock-on feature engaged during use and the

sander is accidentally disconnected from the power supply,

disengage the lock-on feature immediately. Also, do not

lock the switch trigger if you might need to suddenly stop

the sander.

WARNING:

Before connecting the sander to a power supply, make

sure it is not in the locked-on position. Failure to do so

could result in accidental starting of the tool resulting in

serious injury.

To lock-on the sander:

 Depress the switch trigger.

 Push in the lock-on button.

 Release the switch trigger.

 Release the lock-on button.

NOTE: To release the lock, completely squeeze and

release the switch trigger.

OPERATING THE SANDER

See Figure 8, page 12.

 Secure the work to prevent it from moving under the

sander.

WARNING:

Unsecured work could be thrown towards the operator

causing injury.

 Turn the sander on and let the motor reach its maximum

speed before placing the sander on the work surface.

 Lower the sander to the work surface with a slight forward

motion.

 Move the sander slowly over the work surface, using the

rear handle to control the sander and the front handle to

guide the sander.

NOTE: Allowing the sander to remain in one place will

result in an uneven surface.

WARNING:

Keep a firm grip on the sander with both hands at all

times. Failure to do so could result in loss of control lead-

ing to possible serious injury.

The sander is designed to provide the proper weight on the

sanding belt. Excessive pressure will result in the following:

 Uneven work

 Clogged sanding belts

 Premature sanding belt wear

 Possible motor burnout

 Irregular sanding belt tracking

PROPER HAND PLACEMENT

See Figure 9, page 12.

For ease of operation and maintaining proper control, the

sander has a front handle and a rear handle. These handles

allow two-handed operation, which aids in maintaining con-

trol, keeping the sanding area level with the workpiece, and

keeping hands clear of the sanding belt. When operating the

sander, always hold the front handle with your left hand and

the rear handle with your right hand.

WARNING:

Keep hands and fingers clear of moving sanding belt,

front idler roller, and drive roller assembly. Failure to do

so could result in serious personal injury.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Ryobi BE319 Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Ryobi BE319