Ryobi RY80940 Manuel d'utilisateur télécharger pdf (Page 12)

8 — English

ASSEMBLY

UNPACKING

This product requires assembly.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing list

are included.

NOTE: This tool is heavy. To avoid back injury, lift with

your legs, not your back, and get help when needed.

WARNING:

Do not use this product if any parts on the Packing List

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.

 Inspect the tool carefully to make sure no breakage or

damage occurred during shipping.

 Do not discard the packing material until you have carefully

inspected and satisfactorily operated the tool.

 If any parts are damaged or missing, please call

1-800-860-4050 for assistance.

PACKING LIST

Pressure Washer

25 ft. High Pressure Hose

Trigger Handle Holder

Spray Wand Holder

Shoulder Bolt (1/4-20 x 2.27 in.)

Screw (1/4-20 x 1.85 in.)

Shoulder Bolt (1/4-20 x 1.85 in.)

Nut (3)

Trigger Handle

Spray Wand

5-in-1 Change-Over Nozzle

Washer

4-Cycle Engine Lubricant (SAE 30 or SAE 10W30)

Disposable Funnel

High Pressure Hose Storage

Operator’s Manual

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create

accessories not recommended for use with this product.

Any such alteration or modification is misuse and could

result in a hazardous condition leading to possible serious

personal injury.

WARNING:

To prevent accidental starting that could cause serious

personal injury, always disconnect the engine spark plug

wire from the spark plug when assembling parts.

TOOLS NEEDED

See Figure 2.

The following tools (not included or drawn to scale) are

needed for assembly:

 7/16 in. Combination Wrench

 Phillips Screwdriver

RAISING AND LOWERING THE HANDLE

See Figure 3.

 To raise the handle: pull the handle up until the handle

release knob snaps through the locking hole to secure

the handle in place.

 To lower the handle: pull the handle release knob out then

lower the handle to the position shown in figure 3.

INSTALLING TRIGGER HANDLE HOLDER,

SPRAY WAND HOLDER, AND HOSE STORAGE

See Figure 4 - 5.

 Raise handle as described in the Raising and Lowering

Handle section.

 Place hose storage onto the handle as shown.

 Align the holes in the hose storage with the holes in the

handle.

 Insert short shoulder bolt (1/4-20 x 1.85 in.) through the

holes in the left side of the handle and hose storage.

 Place hex nut onto short shoulder bolt and tighten securely.

 Place the trigger handle holder onto the handle as shown.

 Align the holes in the trigger handle holder with the holes

in the hose storage and the handle.

 Insert long shoulder bolt (1/4-20 x 2.27 in.) through the

holes in handle, hose storage, and trigger handle holder.

 Slide washer onto screw. Then, place nut onto screw and

tighten securely.

 Place spray wand holder onto pressure washer frame.

 Align the holes in the spray wand holder with the holes

in the pressure washer frame.

 Insert screw (1/4-20 x 1.85 in.) through the holes in the

spray wand holder and the pressure washer frame.

 Place nut onto screw and tighten securely.

ASSEMBLING THE TRIGGER HANDLE

See Figure 6.

 Place the threaded end of the spray wand in the connector

on the end of the trigger handle.

 Turn the connector clockwise until it stops. This secures

the spray wand in place.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 55 56

Commentaires sur ces manuels

Pas de commentaire

Ryobi RY80940 Manuel d'utilisateur Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Carwash Ryobi RY80940