Ryobi P551 Manuel d'utilisateur télécharger pdf (Page 4)

GENERAL SAFETY RULES

SPECIFIC SAFETY RULES

 FIRMLY CLAMP OR BOLT the tool to a workbench or

table at approximately hip height.

 KEEP HANDS AWAY FROM CUTTING AREA. Do not

reach underneath work or in blade cutting path with hands

and fingers for any reason. Always turn the power off.

 ALWAYS SUPPORT LONG WORKPIECES while cutting

to minimize risk of blade pinching and kickback. Saw may

slip, walk or slide while cutting long or heavy boards.

 ALWAYS USE A CLAMP to secure the workpiece when

possible.

 BE SURE THE BLADE CLEARS THE WORKPIECE.

Never start the saw with the blade touching the

workpiece. Allow motor to come up to full speed

before starting cut.

 MAKE SURE THE MITER TABLE AND SAW ARM

(BEVEL FUNCTION) ARE LOCKED IN POSITION

BEFORE OPERATING THE SAW. Lock the miter table

by pushing the miter lock lever down to lock. Lock the

saw arm (bevel function) by securely tightening the bevel

lock knob.

 USE THIS SAW TO CUT WOOD, WOOD PRODUCTS

AND SOME PLASTICS ONLY. DO NOT CUT METALS,

CERAMICS OR MASONRY PRODUCTS.

 NEVER USE A LENGTH STOP ON THE FREE SCRAP

END OF A CLAMPED WORKPIECE. NEVER hold onto

or bind the free scrap end of the workpiece in any opera-

tion. If a work clamp and length stop are used together,

they must both be installed on the same side of the saw

table to prevent the saw from catching the loose end and

kicking up.

 NEVER cut more than one piece at a time. DO NOT

STACK more than one workpiece on the saw table at a

time.

 NEVER PERFORM ANY OPERATION FREEHAND.

Always place the workpiece to be cut on the miter table

and position it firmly against the fence as a backstop.

Always use the fence.

NEVER START A TOOL WHEN ANY ROTATING COM-

PONENT IS IN CONTACT WITH THE WORKPIECE.

 DO NOT OPERATE A TOOL WHILE UNDER THE

INFLUENCE OF DRUGS, ALCOHOL, OR ANY

MEDICATION.

 WHEN SERVICING use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

 DOUBLE CHECK ALL SETUPS. Make sure blade is

tight and not making contact with saw or workpiece

before connecting to power supply.

 ENSURE THE SWITCH IS IN THE OFF POSITION

BEFORE INSERTING BATTERY PACK. Inserting the

battery pack into power tools that have the switch on

invites accidents.

 RECHARGE ONLY WITH THE CHARGER SPECIFIED

BY THE MANUFACTURER. A charger that is suitabe for

one type of battery pack may create a risk of fire when

used with another battery pack.

 USE POWER TOOLS ONLY WITH SPECIFICALLY DES-

IGNATED BATTERY PACKS. Use of any other battery

packs may create a risk of injury or fire.

 FOR USE WITH 18 V NICKEL-CADMIUM AND 18 V

LITHIUM-ION BATTERY PACKS, see tool/appliance/

battery pack/charger correlation supplement 987000-432.

 WHEN BATTERY PACK IS NOT IN USE, KEEP IT AWAY

FROM OTHER METAL OBJECTS LIKE PAPER CLIPS,

COINS, KEYS, NAILS, SCREWS, OR OTHER SMALL

METAL OBJECTS THAT CAN MAKE A CONNECTION

FROM ONE TERMINAL TO ANOTHER. Shorting the

battery terminals together may cause burns or a fire.

 UNDER ABUSIVE CONDITIONS, LIQUID MAY BE

EJECTED FROM THE BATTERY; AVOID CONTACT. IF

CONTACT ACCIDENTALLY OCCURS, FLUSH WITH

WATER. IF LIQUID CONTACTS EYES, ADDITIONALLY

SEEK MEDICAL HELP. Liquid ejected from the battery

may cause irritation or burns.

 DISCONNECT BATTERY PACK FROM TOOL OR PLACE

THE SWITCH IN THE LOCKED OR OFF POSITION

BEFORE MAKING ANY ADJUSTMENTS, CHANGING

ACCESSORIES, OR STORING THE TOOL. Such pre-

ventive safety measures reduce the risk of starting the

tool accidentally.

TOOL SERVICE MUST BE PERFORMED ONLY BY

QUALIFIED REPAIR PERSONNEL using only identical

replacement parts. This will ensure that the safety of the

power tool is maintained.

1 2 3 4 5 6 7 8 9 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Ryobi P551 Manuel d'utilisateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Scies à moteur Ryobi P551