Ryobi RY64400 Manuel de l'opérateur télécharger pdf (Page 14)

10 - English

OPERATION

USING THE CULTIVATOR FOR EDGING

See Figures 13 - 14.

The cultivator will edge along sidewalks, driveways,

flowerbeds, curbs, and similar areas.

To install the edging tine:

 Remove all tines and felt washers from the shaft.

NOTE: Keep all removable parts in a secure place as they

will be needed when converting back to the cultivating

application.

 Place edging wheel on one side of the tine shaft.

 To secure the edging wheel, place hitch pin into the hole

closest to the gear box.

NOTE: The edging wheel is designed to move along the

shaft. It will not lock into a fixed position.

 Place the tine spacer on the empty side of the tine

shaft.

 Place a felt washer on the tine shaft, then slide to rest

against the tine spacer.

 Place the edging tine onto the the shaft so it rests snuggly

against the felt washer.

 To secure the edging tine place hitch pin into the hole at

the end of the shaft.

To reinstall the cultivating tines:

 Remove edging tine, spacer, edging wheel and felt washer.

 Identify the cultivating tines.

NOTE: The tool has four tines for cultivating — two inner

tines stamped B and C, and two outer tines stamped A

and D. For correct operation of the unit, the tines must

be installed in the correct orientation.

 Lean the unit back on its wheels so that the handlebar

rests on the ground.

NOTE : The view of the gearbox for tine installation is

from the front of the cultivator as shown in Figure 14.

 Place tine C on the tine shaft to the left of the gear box.

The stamped side of the tine should face away from the

gear box.

 Place tine B on the tine shaft to the right of the gear box.

The stamped side of the tine should face away from the

gear box.

 Place a felt washer on each side of the tine shaft, and

slide to rest against the inner tines.

 Place the outer tine labeled D on the left side of the tine

shaft. The stamped side should face in toward tine C.

 Place the outer tine labeled A on the right side of the tine

shaft. The stamped side should face in toward tine B.

NOTE: When installed correctly, the angled edge of the

tines should face the ground.

 To secure the tines to the tine shaft, insert the hitch pin

into the holes located on either side of the tine shaft.

NOTE: The unit will not operate properly if the tines are

installed incorrectly. If you notice a problem with the

cultivating operation of the unit, check for proper tine

positioning.

EDGING TIPS



Cut at a steady pace. If the tine begins to bog down, you

are edging too fast; slow your pace. Do not force the tine

into ground.



Light contact of the tine against the sidewalk edge, curb,

etc., is acceptable and will not damage the cultivator.



Best appearance is obtained when grass is dry. Avoid

edging in wet soil or wet grass areas.

ADJUSTMENTS

WARNING:

To prevent accidental starting that could cause serious

personal injury, always disconnect the spark plug wire

when making adjustments.

ADJUSTING WHEEL/DRAG BAR ASSEMBLY

POSITION

See Figures 15 - 17.

The wheel position of the unit is adjustable. Holes on the

wheel/drag bar assembly support rod offer different heights

to choose from in both the A, B, and C positions.

Switch the wheel/drag bar accessory position to achieve

desired depth.

 Install the wheel/drag bar assembly in position A to trans-

port the cultivator to and from the work area.

 The wheel/drag bar assembly may be installed in position

B for shallow to moderate cultivating depth.

 NOTE: When in position B, the drag bar may be used to

help control the cultivator’s speed and depth of operation.

There are three depth adjustments available in position B.

 For general cultivating, remove the wheel/drag bar as-

sembly (position C) or place it in position B to allow deep

penetration of the tines into the cultivating surface.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 51 52

Commentaires sur ces manuels

Pas de commentaire

Ryobi RY64400 Manuel de l'opérateur Page 14

Commentaires sur ces manuels

Produits connexes et manuels pour Mini-faucheuses Ryobi RY64400