Ryobi SP450 Manuel d'utilisation et d'entretien télécharger pdf (Page 8)

8 – English

OPERATION

WARNING:

Do not allow familiarity with tools to make you care-

less. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes resulting in possible

serious injury.

WARNING:

Do not use any attachments or accessories not

recommended by the manufacturer of this tool. The use

of attachments or accessories not recommended can

result in serious personal injury.

WARNING:

Do not wear loose clothing or jewelry when operating this

product. They could get caught in moving parts causing

serious injury. Keep head away from sander/polisher

and sanding or polishing area. Hair could be drawn into

sander/polisher causing serious injury.

APPLICATIONS

You may use this tool for the purpose listed below:

Sanding on wood and wood product surfaces

Removing rust from and sanding steel surfaces

Polishing and buffing painted surfaces

TWO-SPEED SWITCH TRIGGER

See Figure 2, page 11.

WARNING:

Before connecting the sander/polisher to a power supply,

always make sure it is not in the “locked-on” position.

Failure to do so could result in accidental starting of the

sander resulting in possible serious injury.

The sander/polisher is equipped with a two-speed switch

trigger located in the handle. To turn ON, depress switch

trigger. To turn OFF, release switch trigger. For low speed

sanding or polishing, depress switch trigger halfway. For

high speed sanding or polishing depress switch trigger all

the way. Be sure switch trigger is in OFF position before

connecting to power supply.

LOCK-ON BUTTON

See Figure 2, page 11.

This sander/polisher is equipped with a lock-on feature,

which is convenient for continuous sanding/polishing for

extended periods of time.

To lock-on:

Depress the switch trigger.

Push in and hold the lock-on button, located on the side

of the handle.

Release the switch trigger.

Release the lock-on button and the sander/polisher will

continue running.

To release the lock, depress and release the switch trigger.

If the lock-on feature is engaged during use and the sander/

polisher becomes disconnected from the power supply,

disengage the lock-on feature immediately.

NOTE: Since the sander/polisher has two speeds, it is possible

to lock-on in both speeds. To lock-on in low speed, press

two-speed switch trigger halfway and follow above lock-on

directions for lock-on sanding/polishing. To lock-on at high

speed, depress trigger fully and follow above directions.

INSTALLING/REMOVING POLISHING

BONNET

See Figure 3, page 11.

NOTICE:

Make sure the polishing bonnet is installed with the

polishing surface completely covering the edges of the

rubber pad. Failure to do so may result in the bonnet

tearing, resulting in possible property damage.

Unplug the sander/polisher.

Remove the sanding disc if necessary.

Slip polishing bonnet edges over rubber disc.

To remove, pull polishing bonnet edges over and off rub-

ber disc.

POLISHING

See Figure 4, page 12.

WARNING:

Keep a firm grip on the tool with both hands at all times.

Failure to do so could result in loss of control leading to

possible serious injury.

When polishing, hold the sander/polisher firmly, allowing it

to operate freely without unnecessary pressure. The weight

of the tool alone will provide adequate pressure for polish-

ing at top efficiency. For best results, always operate at low

speed when polishing.

Bonnets must be kept clean and free from grit, dirt, and

other abrasive particles. When bonnets become dirty and

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Ryobi SP450 Manuel d'utilisation et d'entretien Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Ponceuses électriques Ryobi SP450