Ryobi EHG2000 Spécifications télécharger pdf (Page 4)

Safety

protect and retain hair.

■ Make sure you are always well balanced when using

the heat gun.

■ Ensure that the heat gun is always clean, dry and free

from oil or grease.

■ Never force the tool or accessories, and only use them

for the purpose for which they are designed.

■ Always keep the heat gun upright or suspend it with the

stand supplied.

■ Never use the heat gun in a damp or very wet area (for

example: bathrooms, saunas).

■ Never leave the heat gun out in the rain and do not use

it on very damp days.

■ Never push anything down inside the hot air nozzle.

■ Always allow the heat gun to cool down completely

before storing it.

■ Always store the heat gun in a safe place, out of the

reach of children. It is not a toy.

■ This device shall connect to such power supply network

with impedance equal to or less than 0.063 + j0.039

Ω or the agreement with power supplier or user. Any

mismatched connection may cause high voltage

fluctuation.

■ A fire may result if the product is not used with care,

therefore:

– be careful when using the product in places where

there are combustible materials;

– do not apply to the same place for a long time;

– do not use in presence of an explosive atmosphere;

– be aware that heat may be conducted to combustible

materials that are out of sight;

– place the product on its stand after use and allow it

to cool down before storage;

– do not leave the product unattended when it is

switched on.

■ Check the area where the heat gun is to be used.

Behind ceilings, floors and false ceilings may contain

highly flammable material. Always check these before

using the heat gun.

■ Keep the work area clean and uncluttered.

■ Keep the work area well lit.

■ Keep children and visitors away from the work area,

heat gun and any extension cables.

■ To reduce the risk of electric shock, please wear proper

shoes to avoid contact with earthed surfaces.

■ Never carry the heat gun by its power cable or pull on

the cord to disconnect it.

■ Use only suitable extension cables.

■ Inspect the heat gun cable regularly and if damaged,

have it repaired by authorized service centre.

■ When the heat gun is used outdoors, use only extension

cables that are suitable for exterior use.

■ When working on small or irregular shaped objects,

clamp the object in a vice or clip.

■ Ensure the tool switch is at off position before plugging

in.

■ Disconnect the heat gun when it is not in use. Ensure

that the heat gun cannot start accidentally. If the heat

gun stops while it is in use, disconnect it from the power

supply and have it serviced by authorised service

centre.

WARNING

Always concentrate on the job and use common sense

when working with this or any other tools. Do not use this

tool when you are tired or taking medication that may

make you drowsy.

NOTE: Keep the nozzle at least 10 cm away from the

working surface. Heat guns have a safety cut-off which will

stop the heat gun if you are working too close to the surface

being stripped. If the cut-off operates, the heat gun must

be allowed to cool for about 30 minutes before it can be

used again.

■ Never use the heat gun in combination with solvents.

■ After use, remove any paint or varnish residue on the

nozzle and scrapers. This could catch fire.

■ Always work in a well ventilated area. Flakes and

residues of lead-based paints are highly toxic.

SPECIAL SAFETY RULES

■ This product is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience

and knowledge, unless they have been given

supervision or instruction concerning use of the

product by a person responsible for their safety.

Children should be supervised to ensure that they

do not play with the product.

■ Keep children and visitors away. Visitors should wear

safety glasses and be kept as a safe distance from work

area. Do not let visitors contact tool or extension cord.

■ It is recommended that this tool always be supplied via

a residual current device with a rated residual current

of 30mA or less.

INTENDED USE

You may use this product for the purposes listed below:

■ Shrink fitting

■ Bending plastic pipes

■ Thawing frozen pipes

■ Softening adhesives

■ Soft soldering

■ Paint stripping

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Ryobi EHG2000 Spécifications Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Ryobi EHG2000