Ryobi P310 Manuel d'utilisateur télécharger pdf (Page 8)

8 – English

OPERATION

BATTERY PROTECTION FEATURES

Ryobi lithium-ion batteries are designed with features that

protect the lithium-ion cells and maximize battery life.

If the tool stops during use, release the trigger to reset and

resume operation. If the tool still does not work, the battery

needs to be recharged.

WARNING:

Always remove battery pack from your tool when you are

assembling parts, making adjustments, cleaning, or when

not in use. Removing battery pack will prevent accidental

starting that could cause serious personal injury.

TO INSTALL/REMOVE BATTERY PACK

See Figure 2, page 10.

To install:

 Lock the switch trigger by sliding the switch lock up.

 Insert the battery pack into the product as shown.

 Make sure the latches on each side of the battery pack

snap in place and that battery pack is secured in the

product before beginning operation.

To remove:

 Lock the switch trigger by sliding the switch lock up.

 Depress the latches on the side of battery pack.

 Remove the battery pack from the tool.

WARNING:

Battery products are always in operating condition.

Therefore, the switch should always be locked when not

in use or carrying at your side.

STARTING/STOPPING THE CAULK GUN

See Figure 3, page 10.

Before attempting to start the caulk gun, be sure the switch

lock is in the unlocked position.

To turn the caulk gun ON, depress the switch trigger.

To turn the caulk gun OFF, release the switch trigger.

LOCKING THE SWITCH TRIGGER

See Figure 3, page 10.

The switch trigger of the caulk gun can be locked off using

the slide switch located below the switch trigger.

To lock the switch trigger, slide the switch lock up. This

will prevent the caulk gun switch trigger from being de-

pressed.

To unlock the switch trigger, slide the switch down. This

will allow the caulk gun switch trigger to be depressed.

LOADING CAULK

See Figures 4 - 5, page 10.

Lock the switch trigger by sliding the switch lock up.

Using a utility knife, cut off the tip of the spout on a

standard 10 oz. tube of caulk. Cut the tip at a 45˚ angle.

Remove as little as possible, taking into consideration

the size of the “bead” of caulk you need.

Check for a second inner seal at the base of the spout. If

found, insert the puncture tool inside the spout to break

the seal before using. If using a partially filled tube, use

the puncture tool to remove any hardened material from

the tip.

NOTE: An inner seal is usually found only in cardboard

caulk tubes.

While holding the caulk gun steady with one hand, pull

the handle of the plunger rod away from the caulk gun.

Continue pulling until plunger base reaches the back of

the carriage frame.

Load the caulk tube into the carriage frame, making sure

it is well seated at both ends.

ELECTRONIC OVERLOAD PROTECTION

The caulk gun has an electronic overload protection feature.

If too much pressure is exerted on the tube, the motor will

shut down. This helps to prevent damage to the tool and the

caulk tube. If the motor shuts off, make sure that:

Nozzle tip is cut

Inner seal in the caulk tube is broken

Hardened material is removed from the nozzle

Caulk tube is not damaged or frozen

Plunger rod is free of caulk/adhesive materials

Release the trigger and wait for 3 to 5 seconds to allow the

electronics to reset. If the motor again shuts off, move the

variable speed selector to the middle position and press the

trigger again. If the motor continues to shut off, try another

tube of material or take the tool to an authorized service center.

APPLYING CAULK

See Figures 6 - 8, page 10.

Prepare the surface to be caulked by removing any dust,

dirt, or remnants of old caulking. Make sure the area to

be caulked is clean and dry.

Set the speed of the caulk gun to match your application

needs, using just enough caulk to do the job. Experiment

in an out-of-the-way area to find the best speed to use

to deliver the caulk bead you want.

Hold the gun at a slight angle. If filling a crack, insert the

spout into the crack, if possible; otherwise, run the caulk

gun along the surface.

Squeeze the trigger on the caulk gun, allowing the caulk

to extrude from the tube tip.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 27 28

Commentaires sur ces manuels

Pas de commentaire

Ryobi P310 Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Ryobi P310