Ryobi R10511 Manuel d'utilisateur télécharger pdf (Page 6)

Page 6

SPECIFICATIONS:

DRILL-DRIVER R10511 R10521 R10531

Chuck 3/8 in. Keyless 3/8 in. Keyless 1/2 in. Keyless

Motor DC Motor 12.0 V DC Motor 14.4 V DC Motor 18.0 V

Gear Train Two Speed Two Speed Two Speed

Switch Variable Speed Variable Speed Variable Speed

No Load Speed 0-400 RPM (Low) 0-400 RPM (Low) 0-400 RPM (Low)

0-1400 RPM (High) 0-1400 RPM (High) 0-1400 RPM (High)

Clutch 24 Positions 24 Positions 24 Positions

Maximum Torque 250 in./lbs 350 in./lbs 400 in./lbs

CHARGER 1400666/1400677 1400656/1400677 1400667/1400677

Input 120 V, 60 Hz, AC only 120 V, 60 Hz, AC only 120 V, 60 Hz, AC only

Charging Voltage 12.0 V 14.4 V 18.0 V

Charge Rate 1 Hour 1 Hour 1 Hour

OVERLOAD

(For Model R10531 only)

Your drill has a built-in overload protector to protect the motor during overloading or prolonged use. The overload protector

automatically activates to break the circuit. When this occurs, allow your drill to cool a few seconds before resuming

operation.

IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES USING CHARGER PART

NUMBER 1400677

When using your drill-driver continuously, the batteries in your battery pack will become hot. You should let a hot battery

pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack becomes discharged

and is hot, this will cause the red light on your battery charger to flash. When battery pack cools down, red light will glow

continuously indicating fast charging mode, 1 hour charge time. Once the battery pack cools down, it will recharge battery

pack in fast charging mode as normal.

IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES USING CHARGER PART

NUMBER 1400666, 1400656, OR 1400667

When using your drill-driver continuously, the batteries in your battery pack will become hot. You should let a hot battery

pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack becomes discharged

and is hot, this will cause the yellow and green lights on your battery charger to come on instead of the red light. The yellow

and green lights indicate soft start mode and will switch to green only, indicating slow charge mode. The red light indicates

fast charge mode, 1 hour charge time. The green light indicates slow charge mode, requiring overnight charging for

batteries to reach full charge. If the green light comes on after letting battery pack cool down, remove it from charger for

additional cooling.

Once the battery pack cools down, it will recharge battery pack in fast charging mode as normal.

Do not leave a hot battery pack in charger until it cools down. The green light will not go off when battery pack cools. If fast

charge mode is desired, you must physically remove a hot battery pack from the charger, let it cool, then place it back in

charger after it has cooled down. Once the battery pack cools down, it will recharge battery pack in fast charging mode as

normal.

NOTE: This situation only occurs when continuous use of your drill-driver causes the batteries to become hot. It does not

occur under normal circumstances. Refer to "CHARGING YOUR DRILL-DRIVER" for normal recharging of batteries.

If the charger does not charge your battery pack under normal circumstances, return both the battery pack and charger to

your nearest Ryobi Authorized Repair Center for electrical check.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Commentaires sur ces manuels

Pas de commentaire

Ryobi R10511 Manuel d'utilisateur Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Ryobi R10511