Ryobi SSP050 Manuel d'utilisateur télécharger pdf (Page 6)

6 — English

ELECTRICAL

EXTENSION CORDS

Be sure to use an extension cord that has the capacity to

handle the current the product will draw. An undersized cord

will cause a drop in line voltage, resulting in overheating and

loss of power. Use the chart to determine the minimum wire

size required in an extension cord. Only round jacketed cords

listed by Underwriter’s Laboratories (UL) should be used.

When working outdoors with a product, use an extension

cord that is designed for outside use. This type of cord is

designated with “W-A” or “W” on the cord’s jacket.

Before using any extension cord, inspect it for loose or

exposed wires and cut or worn insulation.

A proper extension cord is available at an authorized service

center.

If two extension cords are needed, knot them together to

prevent them from becoming disconnected during use. Make

the knot as shown in ﬁgure 1, then connect the plug end of

once extension cord into the receptacle end of the other.

**Ampere rating (on product data plate)

0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0

Cord Length Wire Size (A.W.G.)

25' 16 16 16 16 14 14

50' 16 16 16 14 14 12

100' 16 16 14 12 10 —

**Used on 12 gauge - 20 amp circuit.

NOTE: AWG = American Wire Gauge

WARNING:

Keep the extension cord clear of the working area.

Position the cord so that it will not get caught on lum-

ber, tools, or other obstructions while you are working

with a power tool. Failure to do so can result in serious

personal injury.

WARNING:

Check extension cords before each use. If damaged

replace immediately. Never use the product with a dam-

aged cord since touching the damaged area could cause

electrical shock resulting in serious injury.

ELECTRICAL CONNECTION

This product is powered by a precision-built electric motor. It

should be connected to a power supply that is 120 V, AC only

(normal household current), 60 Hz. Do not operate this

product on direct current (DC). A substantial voltage drop

will cause a loss of power and the motor will overheat. If

the product does not operate when plugged into an outlet,

double check the power supply.

GROUNDING INSTRUCTIONS

See Figure 1, page 12.

This product must be grounded. In the event of a malfunction

or breakdown, grounding provides a path of least resistance

for electric current to reduce the risk of electric shock.

This product is equipped with an electric cord having an

equipment-grounding conductor and a grounding plug. The

plug must be plugged into a matching outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

Do not modify the plug provided. If it will not ﬁt the outlet,

have the proper outlet installed by a qualiﬁed electrician.

WARNING:

Improper installation of a grounded plug increase the

risk of electric shock. When repair or replacement of the

cord or plug is required, take the tool to an authorized

service center.

Check with a qualiﬁed electrician or service personnel if

the grounding instructions are not completely understood,

or if in doubt as to whether the product is properly

grounded.

Repair or replace a damaged or worn cord immediately.

This product is for use on a nominal 120 V circuit and has a

grounding plug similar to the plug illustrated in ﬁgure 1. Only

connect the product to an outlet having the same conﬁguration

as the plug. Do not use an adapter with this product.

1 2 3 4 5 6 7 8 9 10 11 ... 35 36

Commentaires sur ces manuels

Pas de commentaire

Ryobi SSP050 Manuel d'utilisateur Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Ryobi SSP050