Ryobi JS550L Manuel d'utilisateur télécharger pdf (Page 4)

SPECIFIC SAFETY RULES

n Hold tool by insulated gripping surfaces when per-

forming an operation where the cutting tool may

contact hidden wiring or its own cord. Contact with a

“live” wire will make exposed metal parts of the cutting

tool “live” and shock the operator.

ADDITIONAL SAFETY RULES

n Know your power tool. Read operator’s manual care-

fully. Learn its applications and limitations, as well

as the specific potential hazards related to this tool.

Following this rule will reduce the risk of electric shock,

fire, or serious injury.

n Always wear safety glasses. Everyday eyeglasses

have only impact-resistant lenses; they are NOT safety

glasses. Following this rule will reduce the risk of serious

personal injury.

n Protect your lungs. Wear a face or dust mask if the

operation is dusty. Following this rule will reduce the

risk of serious personal injury.

n Protect your hearing. Wear hearing protection during

extended periods of operation. Following this rule will

reduce the risk of serious personal injury.

n Inspect tool cords periodically and, if damaged, have

repaired at your nearest Authorized Service Center.

Constantly stay aware of cord location. Following this

rule will reduce the risk of electric shock or fire.

n Check damaged parts. Before further use of the

tool, a guard or other part that is damaged should

be carefully checked to determine that it will operate

properly and perform its intended function. Check for

alignment of moving parts, binding of moving parts,

breakage of parts, mounting, and any other conditions

that may affect its operation. A guard or other part that

is damaged should be properly repaired or replaced

by an authorized service center. Following this rule will

reduce the risk of shock, fire, or serious injury.

n Do not abuse cord. Never carry the tool by the cord

or yank it to disconnect it from the receptacle. Keep

cord away from heat, oil, and sharp edges. Following

this rule will reduce the risk of electric shock or fire.

GENERAL SAFETY RULES

SERVICE

n Tool service must be performed only by qualified re-

pair personnel. Service or maintenance performed by

unqualified personnel may result in a risk of injury.

n When servicing a tool, use only identical replacement

parts. Follow instructions in the Maintenance section

of this manual. Use of unauthorized parts or failure to fol-

low Maintenance Instructions may create a risk of shock

or injury.

n Make sure your extension cord is in good condition.

When using an extension cord, be sure to use one

heavy enough to carry the current your product will

draw. A wire gage size (A.W.G.) of at least 14 is recom-

mended for an extension cord 50 feet or less in length.

A cord exceeding 100 feet is not recommended. If in

doubt, use the next heavier gage. The smaller the gage

number, the heavier the cord. An undersized cord will

cause a drop in line voltage resulting in loss of power and

overheating.

n Inspect for and remove all nails from lumber before

using this tool. Following this rule will reduce the risk of

serious personal injury.

n Drugs, alcohol, medication. Do not operate tool while

under the influence of drugs, alcohol, or any medi-

cation. Following this rule will reduce the risk of electric

shock, fire, or serious personal injury.

LASER GUIDE WARNINGS:

The laser guide radiation used in the Ryobi jig saw is

Class IIIa with maximum <5mW and 650nm wavelengths.

These lasers do not normally present an optical hazard

although staring at the beam may cause flash blindness.

n Caution: Use of controls or adjustments or performances

of procedures other than those specified herein may result

in hazardous radiation exposure.

n Avoid direct eye exposure when using the laser guide.

n The laser shall be used and maintained in accordance

with the manufacturer’s instructions.

n Never aim the beam at a person or object other than the

workpiece.

n Always ensure the laser beam is aimed at a sturdy

workpiece without reflective surfaces. Shiny reflective

sheet metal or similar shiny materials are not suitable for

laser use.

n All repairs should be made by an authorized service

representative or the laser manufacturer.

n Save these instructions. Refer to them frequently and

use them to instruct others who may use this tool. If you

loan someone this tool, loan them these instructions

also.

1 2 3 4 5 6 7 8 9 ... 19 20

Commentaires sur ces manuels

Pas de commentaire

Ryobi JS550L Manuel d'utilisateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Scies à moteur Ryobi JS550L