Ryobi WS750L Manuel d'utilisateur télécharger pdf (Page 14)

14 — English

OPERATION

MAKING CUTS

Always draw the line to be cut on the tile using a marker or

grease pencil. If the tile is shiny and hard-to-mark, place

masking tape on the tile and mark the tape.

A common problem when cutting tile is straying from the

marked line. Once you’ve strayed from the mark, you can not

force the wheel back to the line by twisting the tile. Instead,

back up and recut the tile slicing off a small amount of tile

until the wheel is back on track.

To avoid this problem, use the rip guide whenever possible

for making cross cuts and miter cuts.

TO MAKE A CROSS CUT

See Figure 24, page 24.

Cross cuts are straight 90º cuts. The material is fed into the

cut at a 90º angle to the wheel, and the wheel is vertical.

 Using a marker or grease pencil, mark the area to be cut

on material.

 Set the rip guide to 0º, tighten the lock knob, and lock in

place.

 Place the material on the table and firmly against the rip

guide and fence.

 Make sure the material is clear of the cutting wheel before

turning on the saw.

 Turn the on/off switch to the ON position.

 Turn the flow adjustment valve to the ON position.

 Let the cutting wheel build up to full speed and wait for

the wheel to get wet before moving the material into the

wheel.

 Hold the material firmly against the rip guide and feed

the material into the cutting wheel.

 When the cut is made, turn the saw OFF. Wait for the

cutting wheel to come to a complete stop before remov-

ing any part of the material.

TO MAKE A DIAGONAL CUT

See Figure 25, page 25.

Diagonal cuts are also referred to as “long point to long

point cuts”.

 Using a marker or grease pencil, mark the area to be cut

on material.

 Set the rip guide to the desired angle, lock in place, and

tighten the lock knob.

 Place the material on the table and firmly against the rip

guide and fence.

 Make sure the material is clear of the cutting wheel before

turning on the saw.

 Turn the on/off switch to the ON position.

 Turn the flow adjustment valve to the ON position.

 Let the cutting wheel build up to full speed and wait for

the wheel to get wet before moving the material into the

wheel.

 Hold the material firmly against the rip guide and feed

the material into the cutting wheel.

 When the cut is made, turn the saw OFF. Wait for the

cutting wheel to come to a complete stop before remov-

ing any part of the material.

TO MAKE A MITER CUT

See Figure 26, page 25.

Miter cuts are used for cutting outside and inside corners

on material, decorative chair rail, and base molding with the

material at any angle to the wheel other than 90°. Miter cuts

tend to “creep” during cutting. This can be controlled by

holding the workpiece securely against the rip guide.

 Using a marker or grease pencil, mark the area to be cut

on material.

 Set the rip guide to the desired setting, lock in place, and

tighten the lock knob.

 Place the material on the table and firmly against the rip

guide and fence.

 Make sure the material is clear of the cutting wheel before

turning on the saw.

 Turn the on/off switch to the ON position.

 Turn the flow adjustment valve to the ON position.

 Let the cutting wheel build up to full speed and wait for

the wheel to get wet before moving the material into the

wheel.

 Hold the material firmly against the rip guide and feed

the material into the cutting wheel.

 When the cut is made, turn the saw OFF. Wait for the

cutting wheel to come to a complete stop before remov-

ing any part of the material.

TO MAKE AN L-CUT

See Figure 27, page 25.

L-cuts are cuts that remove a piece of tile to fit in a corner,

around a cabinet, or a piece of molding and are made by

two separate cuts.

NOTE: Only overcut on the bottom or underneath side of

the material being cut.

 Using a marker or grease pencil, mark the area to be cut

on both sides of the material.

 Set the rip guide to the desired setting, lock in place, and

tighten the lock knob.

 Place the material on the table and firmly against the rip

guide and fence.

 Make sure the material is clear of the cutting wheel before

turning on the saw.

 Turn the on/off switch to the ON position.

 Turn the flow adjustment valve to the ON position.

 Let the cutting wheel build up to full speed and wait for

the wheel to get wet before moving the material into the

wheel.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 59 60

Commentaires sur ces manuels

Pas de commentaire

Ryobi WS750L Manuel d'utilisateur Page 14

Commentaires sur ces manuels

Produits connexes et manuels pour Scies à moteur Ryobi WS750L