Ryobi P202 Manuel d'utilisateur télécharger pdf (Page 8)

8 – English

OPERATION

KEYLESS CHUCK

See Figure 4, page 11.

The drill has a keyless chuck to tighten or release drill bits

in the chuck jaws. The arrows on the chuck indicate which

direction to rotate the chuck body in order to LOCK (tighten)

or UNLOCK (release) the drill bit.

WARNING:

Do not hold the chuck with one hand and use the power

of the drill to tighten the chuck jaws on the drill bit. The

chuck body could slip in your hand, or your hand could

slip and come in contact with the rotating drill bit. This

could cause an accident resulting in serious personal

injury.

TWO-SPEED GEAR TRAIN (HI-LO)

See Figure 5, page 11.

The drill has a two-speed gear train designed for drilling or

driving at LO (1) or HI (2) speeds. A slide switch is located on

top of the drill to select either LO (1) or HI (2) speed. When

using drill in the LO (1) speed range, speed will decrease

and unit will have more power and torque. When using drill

in the HI (2) speed range, speed will increase and unit will

have less power and torque. Use LO (1) speed for high power

and torque applications and HI (2) speed for fast drilling or

driving applications.

ADJUSTABLE TORQUE CLUTCH

This product is equipped with an adjustable torque clutch

for driving different types of screws into different materials.

The proper setting depends on the type of material and the

size of screw you are using.

ADJUSTING TORQUE

See Figure 6, page 11.

There are twenty-four torque indicator settings located on

the front of the drill.

 Rotate the adjusting ring to the desired setting.

• 1-4 Fordrivingsmallscrews

• 5-8 Fordrivingscrewsintosoftmaterial

• 9-12 Fordrivingscrewsintosoftandhard 

materials

• 13-16 Fordrivingscrewsintohardwood

• 17-20 Fordrivinglargescrews

• 21- For heavy drilling

INSTALLING BITS

See Figures 7 - 8, page 12.

 Lock the switch trigger by placing the direction of rotation

selector in the center position.

 Open or close the chuck jaws to a point where the opening

is slightly larger than the bit size you intend to use. Also,

raise the front of the drill slightly to keep the bit from falling

out of the chuck jaws.

Insert the drill bit.

WARNING:

Make sure to insert the drill bit straight into the chuck

jaws. Do not insert the drill bit into the chuck jaws at an

angle then tighten, as shown in figure 9. This could cause

the drill bit to be thrown from the drill, resulting in possible

serious personal injury or damage to the chuck.

Tightenthechuckjawssecurelyonthebit.

NOTE: Rotate the chuck body in the direction of the

arrow marked LOCK to close the chuck jaws. Do not use

a wrench to tighten or loosen the chuck jaws.

REMOVING BITS

See Figure 7, page 12.

Lock the switch trigger by placing the direction of rotation

selector in the center position.

Open the chuck jaws.

NOTE: Rotate the chuck body in the direction of the arrow

marked UNLOCK to open the chuck jaws. Do not use a

wrench to tighten or loosen the chuck jaws.

 Remove the drill bit.

DRILLING

See Figure 9, page 12.

A level is located on the top of the motor housing to help

keep the drill bit level during use.

 Check the direction of rotation selector for the correct

setting(forwardorreverse).

 Secure the material to be drilled in a vise or with clamps

tokeepitfromturningasthedrillbitrotates.

 Hold the drill firmly and place the bit at the point to be

drilled.

 Depress the switch trigger to start the drill.

 Move the drill bit into the workpiece, applying only enough

pressure to keep the bit cutting. Do not force the drill or

apply side pressure to elongate a hole. Let the tool do

the work.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Ryobi P202 Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Ryobi P202