Ryobi R10630 Manuel d'utilisateur télécharger pdf (Page 8)

Page 8

OPERATION

WARNING:

Always wear safety goggles or safety glasses with side

shields when operating tools. Failure to do so could result

in objects being thrown into your eyes, resulting in possible

serious injury.

WARNING:

Do not allow familiarity with your circular saw to make you

careless. Remember that a careless fraction of a second

is sufficient to inflict severe injury.

CHARGING BATTERY PACK WITH CHARGER

PART NUMBER 1400667

The battery pack for this tool has been shipped in a low

charge condition to prevent possible problems. Therefore,

you should charge it until light on front of charger changes

from red to green.

NOTE: Batteries will not reach full charge the first time they

are charged. Allow several cycles (cutting followed by

recharging) for them to become fully charged.

TO CHARGE

■ Connect charger to power supply.

■ Charge battery pack only with the charger provided.

■ Make sure power supply is normal house voltage,

120 volts, 60 Hz, AC only.

■ Connect charger to power supply.

■ Place battery pack in charger aligning raised rib in

charger with groove in battery pack.

■ Press down on battery pack to be sure contacts on

battery pack engage properly with charger contacts.

■ Normally, the yellow and green lights on charger will

come on. This indicates charger is in soft start mode and

should switch to fast charge mode within 5 minutes.

When charger is in fast charge mode the red light will

come on. If after a period of 15 minutes the yellow and

green lights remain on, remove battery pack, wait 1

minute and reinsert battery pack in charger. If the yellow

and green lights continue to remain on after an additional

15 minutes, the battery pack is damaged and will not

accept a charge. Return battery pack to your nearest

Ryobi Authorized Service Center for checking or replac-

ing.

■ When your battery pack becomes fully charged, the red

light will turn OFF and the green light will turn ON.

■ After normal usage, 1 hour of charging time is required to be

fully charged. A minimum charge time of 1-1/2 hours is required

to recharge a completely discharged tool.

■ The battery pack will become slightly warm to the touch while

charging. This is normal and does not indicate a problem.

■ Do not place charger in an area of extreme heat or cold.

It will work best at normal room temperature.

■ When the batteries become fully charged, unplug your

charger from power supply and remove the battery pack.

LED FUNCTION OF CHARGER

LED WILL BE LIGHTED TO INDICATE STATUS OF

CHARGER AND BATTERY PACK:

■ Red LED Lighted = Fast Charging Mode.

■ Green LED Lighted = Fuly Charged Or In Slow Charging

Mode To Maintain Battery Pack.

■ Yellow and Green LED Lighted = Soft Start Mode, or After

1/2 Hour Equals Hot or Defective Battery Pack.

IMPORTANT INFORMATION FOR RECHARG-

ING HOT BATTERIES USING CHARGER

PART NUMBER 1400667

See Figure 2.

When using your circular saw continuously, the batteries in

your battery pack will become hot. You should let a hot

battery pack cool down for approximately 30 minutes be-

fore attempting to recharge. When the battery pack be-

comes discharged and is hot, this will cause the yellow and

green lights on your battery charger to come on instead of

the red light. The yellow and green lights indicate soft start

mode and will switch to green only, indicating slow charge

mode. The red light indicates fast charge mode, 1 hour

charge time. The green light indicates slow charge mode,

requiring overnight charging for batteries to reach full charge.

If the green light comes on after letting battery pack cool

down, remove it from charger for additional cooling.

Once the battery pack cools down, it will recharge battery

pack in fast charging mode as normal.

Do not leave a hot battery pack in charger until it cools

down. The green light will not go off when battery pack

cools. If fast charge mode is desired, you must physically

remove a hot battery pack from the charger, let it cool, then

place it back in charger after it has cooled down.

NOTE: This situation only occurs when continuous use of

your saw causes the batteries to become hot. It does not

occur under normal circumstances. Refer to "CHARG-

ING BATTERY PACK WITH CHARGER PART NUMBER

1400667" for normal recharging of batteries. If the charger

does not charge your battery pack under normal circum-

stances, return both the battery pack and charger to your

nearest Ryobi Authorized Repair Center for electrical check.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 21 22

Commentaires sur ces manuels

Pas de commentaire

Ryobi R10630 Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Ryobi R10630