Ryobi EMS-1422L Manuel d'utilisateur télécharger pdf (Page 8)

English

FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR

WARNING

Unsecured workpieces could be thrown towards the

operator, causing injury.

WARNING

Keep your head away from the sander and the sanding

area. Your hair could be drawn into the sander causing

serious injury.

2. Place the sander on the workpiece so that all of the

sanding disc surface is in contact with the workpiece.

CAUTION

Avoid damaging the motor from overheating; be careful

not to let your hand cover the air vents.

3. Turn on the sander and move it slowly over the

workpiece.

NOTE: Hold the sander in front and away from you,

keeping it clear of the workpiece. Start sander and let the

motor build to its maximum speed, then gradually lower

the sander onto the workpiece. Move the sander slowly

across the workpiece using small circular motions.

Do not force. The weight of the unit supplies adequate

pressure, so let the sanding disc and sander do the work.

Applying additional pressure only slows the motor, rapidly

wears sanding disc and greatly reduces sander speed.

Excessive pressure will overload the motor causing

possible damage from motor overheating and can result in

inferior work. Any  nish or resin on wood may soften from

the frictional heat.

Do not allow sanding on one spot too long as the sander’s

rapid action may remove too much material, making the

surface uneven.

Extended periods of sanding may tend to overheat the

motor. If this occurs, turn sander off and wait until sanding

disc comes to a complete stop, then remove it from

workpiece. Remove your hand from vent area, remove

sanding disc, then with your hand removed from vent

area, turn sander on and run it free without a load to cool

motor.

CORNERS AND CREVICES

See Figure 6.

 For detail sanding such as corners and crevices, use

the tip of the sanding pad with small back and forth

motions.

EMPTYING THE DUST COLLECTION BOX

See Figure 7.

For more ef cient operation, empty the dust collection

box when it is no more than half full. Always empty and

clean the dust collection box thoroughly upon completion

of a sanding operation and before placing the sander in

storage.

WARNING

Collected sanding dust from sanding surface coatings

such as polyurethanes, linseed oil, etc., can self-ignite

in your sander dust collection box or elsewhere and

cause  re. To reduce the risk of  re always empty your

dust collection box frequently (10-15 minutes) while

sanding and never store or leave a sander without

totally emptying its dust collection box. Also follow the

recommendations of the coatings manufacturers.

1. Unplug the sander.

WARNING

Failure to unplug the tool could result in accidental

starting causing possible serious injury.

2. Remove the dust collection box from the sander.

3. Shake out the dust.

4. Reattach the dust collection box to the sander.

NOTE: For a more thorough cleaning of the dust collection

box, remove dust collection box from frame and shake out

dust. Replace dust collection box over frame then install

dust collection box assembly on sander.

CHANGING THE BASE PADS

Sheet and triangular pad

See Figure 8.

1. For safety reasons, ensure your tool is unplugged.

2. Remove the sanding sheet from the base. Undo the

allen screws on the base, using the hex key provided.

3. Once all 3 screws have been removed, remove the

base.

4. When  tting the new base, place the base up to the

sander and insert the  rst screw (do not tighten).

5. Insert the remaining 2 screws, then tighten all 3

screws. Tighten up the allen screws opposite to each

other.

Place the desired sanding paper on to the base and

continue to work.

CAUTION

Remove the sanding sheet when not in use to prevent

warping.

1 2 3 4 5 6 7 8 9 10

Commentaires sur ces manuels

Pas de commentaire

Ryobi EMS-1422L Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Ponceuses électriques Ryobi EMS-1422L