Ryobi P421 Manuel d'utilisation et d'entretien télécharger pdf (Page 3)

3 — English

SAFETY WARNINGS COMMON FOR GRIND-

ING, SANDING, WIRE BRUSHING AND POLISH-

ING OPERATIONS

 This power tool is intended to function as a grinder,

sander, wire brush, or polisher. Read all safety warn-

ings, instructions, illustrations and specifications

provided with this power tool. Failure to follow all

instructions listed below may result in electric shock, fire

and/or serious injury.

 Operations such as cutting-off are not recommended

to be performed with this power tool. Operations for

which the power tool was not designed may create a

hazard and cause personal injury.

 Do not use accessories which are not specifically

designed and recommended by the tool manufacturer.

Just because the accessory can be attached to your

power tool, it does not assure safe operation.

The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated speed

can break and fly apart.

 The outside diameter and the thickness of your acces-

sory must be within the capacity rating of your power

tool. Incorrectly sized accessories cannot be adequately

guarded or controlled.

 Threaded mounting of accessories must match the

grinder spindle thread. For accessories mounted by

flanges, the arbour hole of the accessory must fit the

locating diameter of the flange. Accessories that do not

match the mounting hardware of the power tool will run

out of balance, vibrate excessively and may cause loss

of control.

 Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for

chips and cracks, backing pad for cracks, tear or

excess wear, wire brush for loose or cracked wires.

If power tool or accessory is dropped, inspect for

damage or install an undamaged accessory. After

inspecting and installing an accessory, position your-

self and bystanders away from the plane of the rotat-

ing accessory and run the power tool at maximum

no-load speed for one minute. Damaged accessories

will normally break apart during this test time.

 Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron capable of

stopping small abrasive or workpiece fragments.

The eye protection must be capable of stopping flying

debris generated by various operations. The dust mask or

respirator must be capable of filtrating particles generated

by your operation. Prolonged exposure to high intensity

noise may cause hearing loss.

Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

BATTERY TOOL USE AND CARE

Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another battery pack.

Use power tools only with specifically designated

battery packs. Use of any other battery packs may create

a risk of injury and fire.

When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys, nails,

screws or other small metal objects, that can make

a connection from one terminal to another. Shorting

the battery terminals together may cause burns or a fire.

Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, flush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected from the

battery may cause irritation or burns.

SERVICE

Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

When servicing a power tool, use only identical

replacement parts. Follow instructions in the

Maintenance section of this manual. Use of unauthorized

parts or failure to follow Maintenance instructions may

create a risk of shock or injury.

GENERAL POWER TOOL SAFETY WARNINGS

ANGLE GRINDER SAFETY WARNINGS

1 2 3 4 5 6 7 8 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Ryobi P421 Manuel d'utilisation et d'entretien Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Ryobi P421