Ryobi MS181 Manuel de l'opérateur télécharger pdf (Page 3)

Page 3

READ ALL INSTRUCTIONS

■ KNOW YOUR POWER TOOL. Read the

operator's manual carefully. Learn the saw's

applications and limitations as well as the

specific potential hazards related to this tool.

■ GUARD AGAINST ELECTRICAL SHOCK BY

PREVENTING BODY CONTACT WITH

GROUNDED SURFACES. For example; pipes,

radiators, ranges, refrigerator enclosures.

■ KEEP GUARDS IN PLACE and in good working

order.

■ REMOVE ADJUSTING KEYS AND

WRENCHES. Get in the habit of checking to see

that hex keys and adjusting wrenches are

removed from tool before turning on saw.

■ KEEP THE WORK AREA CLEAN. Cluttered

work areas and work benches invite accidents.

DO NOT leave tools or pieces of wood on the

saw while it is in operation.

■ DO NOT USE IN DANGEROUS ENVIRON-

MENTS. Do not use power tools near gasoline or

other flammable liquids, in damp or wet loca-

tions, or expose them to rain. Keep the work

area well lit.

■ KEEP CHILDREN AND VISITORS AWAY. All

visitors should wear safety glasses and be kept a

safe distance from work area. Do not let visitors

contact tool while operating.

■ MAKE WORKSHOP CHILD-PROOF with

padlocks and master switches, or by removing

starter keys.

■ DO NOT FORCE THE TOOL. It will do the job

better and safer at the rate for which it was

designed.

■ USE THE RIGHT TOOL. Do not force the tool or

attachment to do a job it was not designed for.

Don't use it for a purpose not intended.

■ USE THE PROPER EXTENSION CORD FOR

CHARGER. Make sure your extension cord is in

good condition. When using an extension cord,

be sure to use one heavy enough to carry the

current your product will draw. An undersized

cord will cause a drop in line voltage resulting in

loss of power and overheating. A wire gage size

(A.W.G.) of at least 16 is recommended for an

extension cord 25 feet or less in length. If in

doubt, use the next heavier gage. The smaller

the gage number, the heavier the cord.

■ PERIODICALLY INSPECT EXTENSION

CORDS and replace if damaged.

■ DRESS PROPERLY. Do not wear loose clothing,

gloves, neckties, rings, bracelets, or other jewelry.

They can get caught and draw you into moving

parts. Rubber gloves and nonslip footwear are

recommended when working outdoors. Also wear

protective hair covering to contain long hair.

■ ALWAYS WEAR SAFETY GLASSES WITH

SIDE SHIELDS. Everyday eyeglasses have only

impact-resistant lenses; they are NOT safety

glasses.

■ PROTECT YOUR LUNGS. Wear a face or dust

mask if the cutting operation is dusty.

■ PROTECT YOUR HEARING. Wear hearing

protection during extended periods of operation.

■ SECURE WORK. Use clamps or a vise to hold

work when practical. It's safer than using your

hand and it frees both hands to operate tool.

■ DO NOT OVERREACH. Keep proper footing and

balance at all times.

■ MAINTAIN TOOLS WITH CARE. Keep tools

sharp and clean for better and safer perfor-

mance. Follow instructions for lubricating and

changing accessories.

■ DISCONNECT ALL TOOLS. When not in use,

before servicing, or when changing attachments,

blades, bits, cutters, etc., all tools should be

disconnected or battery pack removed.

■ AVOID ACCIDENTAL STARTING. Be sure

switch is in the locked or off position before

inserting battery pack. Carrying tools with your

finger on the switch or inserting the battery pack

into a tool with the switch on invites accidents.

■ USE RECOMMENDED ACCESSORIES. The use

of improper accessories may cause risk of injury.

Refer to this operator's manual for recommended

accessories.

■ NEVER STAND ON TOOL. Serious injury could

occur if the tool is tipped or if the blade is unin-

tentionally contacted.

■ CHECK DAMAGED PARTS. Before further use

of the tool, a guard or other part that is damaged

should be carefully checked to determine that it

will operate properly and perform its intended

function. Check for alignment of moving parts,

binding of moving parts, breakage of parts,

mounting and any other conditions that may

affect its operation. A guard or other part that is

damaged must be properly repaired or replaced

by an authorized service center to avoid risk of

personal injury.

RULES FOR SAFE OPERATION

1 2 3 4 5 6 7 8 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Ryobi MS181 Manuel de l'opérateur Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Scies à onglets Ryobi MS181