Ryobi ZRCSB133L Manuel d'utilisation et d'entretien télécharger pdf (Page 5)

5 - English

CIRCULAR SAW SAFETY WARNINGS AND INSTRUCTIONS

 Support large panels to minimise the risk of blade

pinching and kickback. Large panels tend to sag under

their own weight. Supports must be placed under the

panel on both sides, near the line of cut and near the

edge of the panel.

 Do not use dull or damaged blades. Unsharpened

or improperly set blades produce narrow kerf causing

excessive friction, blade binding and kickback.

 Blade depth and bevel adjusting locking levers must be

tight and secure before making cut. If blade adjustment

shifts while cutting, it may cause binding and kickback.

 Use extra caution when making a “plunge cut” into

existing walls or other blind areas. The protruding blade

may cut objects that can cause kickback.

 Check lower guard for proper closing before each use.

Do not operate saw if lower guard does not move freely

and close instantly. Never clamp or tie the lower guard

into the open position. If saw is accidentally dropped,

lower guard may be bent. Raise the lower guard with the

retracting handle and make sure it moves freely and does

not touch the blade or any other part, in all angles and

depths of cut.

 Check the operation of the lower guard spring. If the

guard and the spring are not operating properly, they

must be serviced before use. Lower guard may operate

sluggishly due to damaged parts, gummy deposits, or a

build-up of debris.

 Lower blade guard handle should be retracted manu-

ally only for special cuts, such as “plunge cuts” and

“compound cuts.” Raise lower guard by retracting

handle and as soon as blade enters the material, the

lower guard must be released. For all other sawing, the

lower guard should operate automatically.

 Always observe that the lower guard is covering the

blade before placing saw down on bench or floor. An

unprotected, coasting blade will cause the saw to walk

backwards, cutting whatever is in its path. Be aware of the

time it takes for the blade to stop after switch is released.

ADDITIONAL SAFETY RULES

 Hold power tools by insulated gripping surfaces when

performing an operation where the cutting tool may

contact hidden wiring or its own cord. Contact with a

“live” wire will make exposed metal parts of the tool “live”

and shock the operator.

 Know your power tool. Read operator’s manual care-

fully. Learn its applications and limitations, as well

as the specific potential hazards related to this tool.

Following this rule will reduce the risk of electric shock,

fire, or serious injury.

 Always wear eye protection with side shields marked

to comply with ANSI Z87.1. Failure to do so could result

in objects being thrown into your eyes, resulting in pos-

silbe serious injury.

 Protect your lungs. Wear a face or dust mask if the

operation is dusty. Following this rule will reduce the

risk of serious personal injury.

 Protect your hearing. Wear hearing protection during

extended periods of operation. Following this rule will

reduce the risk of serious personal injury.

 Inspect tool cords periodically and, if damaged, have

repaired at your nearest authorized service center.

Constantly stay aware of cord location. Following this

rule will reduce the risk of electric shock or fire.

 Check damaged parts. Before further use of the

tool, a guard or other part that is damaged should

be carefully checked to determine that it will operate

properly and perform its intended function. Check for

alignment of moving parts, binding of moving parts,

breakage of parts, mounting, and any other conditions

that may affect its operation. A guard or other part that

is damaged should be properly repaired or replaced

by an authorized service center. Following this rule will

reduce the risk of shock, fire, or serious injury.

 Make sure your extension cord is in good condi-

tion. When using an extension cord, be sure to use

one heavy enough to carry the current your product

will draw. A wire gauge size (A.W.G.) of at least 14 is

recommended for an extension cord 25 feet or less

in length. A cord exceeding 100 feet is not recom-

mended. If in doubt, use the next heavier gauge. The

smaller the gauge number, the heavier the cord. An

undersized cord will cause a drop in line voltage resulting

in loss of power and overheating.

 Inspect for and remove all nails from lumber before

using this tool. Following this rule will reduce the risk of

serious personal injury.

 Do not wear loose clothing or jewellery. Contain long

hair. Loose clothes, jewellery, or long hair can be drawn

into air vents.

 Do not use on a ladder or unstable support. Stable

footing on a solid surface enables better control of the

tool in unexpected situations.

If the power supply cord is damaged, it must be

replaced only by the manufacturer or by an authorized

service center to avoid risk.

 Save these instructions. Refer to them frequently and

use them to instruct others who may use this tool. If you

loan someone this tool, loan them these instructions also.

1 2 3 4 5 6 7 8 9 10 ... 51 52

Commentaires sur ces manuels

Pas de commentaire

Ryobi ZRCSB133L Manuel d'utilisation et d'entretien Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Ryobi ZRCSB133L