Ryobi HG500 Manuel d'utilisateur Page 23
- Page / 46
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
453
8
Abrasives and Industrial Brushes
Weiler Brush
Vendor Code: WB
Benchstand Belt
Sander
Weiler's Satisfaction Guarantee
Weiler Corporation hereby warrants that its Power Brush, Nylox
®
, Abrasive and Maintenance products shall be free from defects in material and
workmanship under normal use and service, for a period of one year from the date of purchase. In the event the customer reasonably becomes dissatisfi ed
with the performance of any of Weiler's products, Weiler will repair or replace the product at no cost to the customer. This repair or replacement is
contingent upon prompt written notice and compliance by the customer with instructions given by Weiler regarding the return of the product for evaluation.
This warranty is expressly in lieu of all other warranties, expressed or implied, including the warranties of merchantability and fi tness for a particular purpose.
Correction in the manner provided hereinabove shall be the extent of Weiler's liability, and no other entity is authorized to extend that liability.
Safety Goggles
Safety goggles or full face shields
worn over safety glasses with
side shields MUST BE WORN BY
ALL OPERATORS AND OTHERS
IN THE AREA OF BRUSH AND
ABRASIVE OPERATIONS. Comply
with the requirements of ANSI Z87.1
“Occupational Eye and Face
Protection”.
Guards
Keep all machine guards in place.
Speeds
Observe all speed restrictions
indicated on brushes, abrasives,
containers, labels, or printed in
pertinent literature. MSFS means
Maximum Safe Free Speed
(RPM)−spinning free with no work
applied. For reasons of safety, MSFS
or Maximum RPM should not be
exceeded under any circumstances.
Protective Equipment
Appropriate protective clothing and
equipment must be used where there
is a possibility of injury that can be
prevented by such clothing or
equipment.
Tool/Work Rest
On bench grinders and pedestal
machines, tool/work rests should be
used to support the work-piece during
use. It should have a maximum
opening of 1/8" to the product face.
Only adjust the rest when the product
is not in motion.
Safety Standards
Comply with the Safety Standards
of the American National Standards
Institute Standards ANSI B165.1
“Safety Requirements - Power
Brushes” and ANSI B7.1 “Safety
Requirements - For the Use, Care
and Protection of Abrasive Wheels”.
Power Tool Icons
Straight
Grinder
Right Angle
Grinder
Bench/Pedestal
Grinder
Die Grinder Right Angle
Air Die Grinder
Stationary
Belt Sander
Portable File
Belt Sander
Portable Belt
Sander
Cut-Off
Die Grinder
High Speed
Pencil Grinder
Chop Saw Circular SawPortable Chop
Saw
Stationary
Cut-Off Machine
Low HP
Chop Saw
Safety Information
Safety Information
WARNING
Failure to observe safety
precautions may result in injury.
Drill Press Flexible
Shaft Tool
Availability of
ANSI Standards
Based on the collective experience
of the ABMA Industrial Division
members (ANSI B165.1) and the
United Abrasives Manufacturers
Association’s Bonded Division
(ANSI B7.1), both ANSI Standards
are referenced and provided
solely as a public service for
the guidance of the users of the
members’ products. All Brush and
Abrasive recommendations are not
necessarily complete with respect
to any particular application and
common sense safety considerations
should be adhered to generally. Any
applicable federal, state, local law or
regulation must be strictly adhered
to and is controlling over any
recommendation contained herein.
American National Standards are
subject to periodic review and users
are cautioned to obtain the latest
editions. Contact The American
National Standards Institute (ANSI),
1430 Broadway, New York, NY 10018.
These icons illustrate the power tools used to drive Weiler brushed and abrasives.
www.middlesexgases.com
- A 24 R 1
- Cutting Wheels 2
- Weiler Brush 3
- Vendor Code: WB 3
- A 24 T 4
- Cut-off Wheel 5
- Tiger Disc 7
- Trimmable Tiger Disc 8
- Vortec Pro 10
- Abrasive Flap Discs 10
- Specialty Abrasive Flap Discs 11
- Coated Abrasive Shop Rolls 13
- Solving User Problems 13
- Resin Fiber Discs 14
- AL-tra CUT 15
- Coated Abrasive Flap Wheels 16
- Blending Discs 17
- Trim-Kut 18
- Coated Abrasive Belts 19
- Non-Woven Hand Pads 21
- Surface Conditioning Discs 21
- Industrial Brushes 22
- Safety Information 23
- S U R F A C E F I N I S H 24
- A G G R E S S I O N 24
- Overall Length 25
- Stainless Steel Wire Brushes: 26
- Product Selection 27
- Application Solutions Guide 29
- Crimped Wire Wheels 30
- Crimped Wire Wheels 31
- Copper Center 31
- - Small Diameter Wire Wheels 31
- Duralife 32
- Knot Wire Wheels 32
- Knot Wire Cup Brushes 34
- Mighty-Mite 35
- Stem-Mounted Brushes 40
- Power and Hand Tube Brushes 41
- Floor Brushes 42
- Handles and Accessories 42
- Counter Dusters and Dust Pans 42
- Miscellaneous Brushes 43
- Scratch Brushes 44
- Industrial Accessories 46
Produits connexes et manuels pour Outils électriques Ryobi HG500
(24 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.085 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels