Ryobi RLS1351 Manuel de l'opérateur télécharger pdf (Page 5)

 KEEP HANDS AWAY FROM CUTTING AREA. Do not

reach underneath work or in blade cutting path with hands

and ﬁngers for any reason. Always turn the power off.

 ALWAYS SUPPORT LONG WORKPIECES while cutting

to minimize risk of blade pinching and kickback. Saw may

slip, walk or slide while cutting long or heavy boards.

 ALWAYS USE THE WORK CLAMP to secure the

workpiece when making cross cuts.

 BE SURE THE BLADE CLEARS THE WORKPIECE.

Never start the saw with the blade touching the

workpiece. Allow motor to come up to full speed

before starting cut.

 NEVER cut more than one piece at a time. DO NOT

STACK more than one workpiece on the saw table at a

time.

 NEVER PERFORM ANY OPERATION FREEHAND.

Always place the workpiece to be cut on the saw table

and position it ﬁrmly against the fence as a backstop.

Always use the fence.

 NEVER hand hold a workpiece that is too small to be

clamped. Keep hands clear of the cutting area.

 NEVER reach behind, under, or within three inches of the

blade and its cutting path with hands and ﬁngers for any

reason.

 NEVER reach to pick up a workpiece, a piece of scrap,

or anything else that is in or near the cutting path of the

blade.

NEVER move the workpiece or make adjustment to any

cutting angle while the saw is running and the blade is

rotating. Any slip can result in contact with the blade

causing serious personal injury.

 AVOID AWKWARD OPERATIONS AND HAND

POSITIONS where a sudden slip could cause your hand

to move into the blade. ALWAYS make sure you have

good balance.

 NEVER stand or have any part of the body in line with

the path of the saw blade.

 ALWAYS release the power switch and allow the saw blade

to stop rotating before raising it out of the workpiece.

 DO NOT TURN THE MOTOR SWITCH ON AND OFF

RAPIDLY. This could cause the saw blade to loosen

and could create a hazard. Should this ever occur,

stand clear and allow the saw blade to come to a

complete stop. Disconnect your saw from the power

supply and securely retighten the blade bolt.

SPECIFIC SAFETY RULES

 IF ANY PART OF THIS SAW IS MISSING or should

break, bend, or fail in any way, or should any electrical

component fail to perform properly, shut off the power

switch, remove the saw plug from the power source and

have damaged, missing, or failed parts replaced before

resuming operation.

 ALWAYS STAY ALERT! Do not allow familiarity (gained

from frequent use of the saw) to cause a careless

mistake. ALWAYS REMEMBER that a careless frac-

tion of a second is sufﬁcient to inﬂict severe injury.

 IF THE POWER SUPPLY CORD IS DAMAGED, it must

be replaced only by the manufacturer or by an authorized

service center to avoid risk.

 MAKE SURE WORK AREA HAS AMPLE LIGHTING to

see the work and that no obstructions will interfere with

safe operation BEFORE performing any work using the

saw.

 ALWAYS TURN OFF THE SAW before disconnecting it

to avoid accidental starting when reconnecting to power

supply. NEVER leave the saw unattended while connected

to a power source.

 TURN THE SAW OFF. Wait for the blade to come to a

complete stop before removing the workpiece.

 THIS TOOL should have the following markings:

a) Wear eye protection.

b) Keep hands and body out of path of saw blade.

c) Do not operate saw without guards in place.

d) Do not perform any operation freehand.

e) Never reach around or over saw blade.

f) Turn off tool and wait for saw blade to stop before

moving workpiece or changing settings.

g) Disconnect power (or unplug tool as applicable)

before changing blade or servicing.

h) Return saw to rear of tool after each cross cut.

i) Use a push stick for narrow work and when

required.

j) Pay particular attention to instruction on reducing

risk of kickback.

 ALWAYS MAKE SURE THE SAW BLADE HAS CLEAR-

ANCE OF ALL OBSTRUCTIONS BEFORE TURNING

THE SAW ON.

 ALWAYS carry the tool only by the carrying handle.

 SAVE THESE INSTRUCTIONS. Refer to them

frequently and use to instruct other users. If you loan

someone this tool, loan them these instructions also.

1 2 3 4 5 6 7 8 9 10 ... 55 56

Commentaires sur ces manuels

Pas de commentaire

Ryobi RLS1351 Manuel de l'opérateur Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Ryobi RLS1351