Ryobi AG453K Manuel d'utilisateur télécharger pdf (Page 3)

3 - English

SPECIFIC SAFETY RULES

SAFETY WARNINGS COMMON FOR GRIND-

ING, SANDING, WIRE BRUSHING AND POLISH-

ING OPERATIONS

 This power tool is intended to function as a grinder,

sander, wire brush, or polisher. Read all safety warn-

ings, instructions, illustrations and specifications

provided with this power tool. Failure to follow all in-

structions listed below may result in electric shock, fire

and/or serious injury.

 Operations such as cutting-off are not recommended

to be performed with this power tool. Operations for

which the power tool was not designed may create a

hazard and cause personal injury.

 Do not use accessories which are not specifically

designed and recommended by the tool manufacturer.

Just because the accessory can be attached to your

power tool, does not assure safe operation.

The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their RATED SPEED

can break and fly apart.

 The outside diameter and the thickness of your acces-

sory must be within the capacity rating of your power

tool. Incorrectly sized accessories cannot be adequately

guarded or controlled.

 The arbour size of wheels, flanges, backing pads or

any other accessory must properly fit the spindle of

the power tool. Accessories with arbour holes that do

not match the mounting hardware of the power tool will

run out of balance, vibrate excessively and may cause

loss of control.

 Do not use a damaged accessory. Before each use in-

spect the accessory such as abrasive wheels for chips

and cracks, backing pad for cracks, tear or excess

wear, wire brush for loose or cracked wires. If power

tool or accessory is dropped, inspect for damage or

install an undamaged accessory. After inspecting and

installing an accessory, position yourself and bystand-

ers away from the plane of the rotating accessory and

run the power tool at maximum no-load speed for one

minute. Damaged accessories will normally break apart

during this test time.

 Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron capable of

stopping small abrasive or workpiece fragments.

The eye protection must be capable of stopping

flying debris generated by various operations. The

eye protection must be capable of stopping flying debris

generated by various operations. The dust mask or

respirator must be capable of filtrating particles generated

by your operation. Prolonged exposure to high intensity

noise may cause hearing loss.

 Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal

protective equipment. Fragments of workpiece or of a

broken accessory may fly away and cause injury beyond

immediate area of operation.

Hold power tool by insulated gripping surfaces only,

when performing an operation where the cutting ac-

cessory may contact hidden wiring or its own cord.

Cutting accessory contacting a ²live² wire may make

exposed metal parts of the power tool ²live² and shock

the operator.

 Position the cord clear of the spinning accessory. If

you lose control, the cord may be cut or snagged and your

hand or arm may be pulled into the spinning accessory.

 Never lay the power tool down until the accessory

has come to a complete stop. The spinning accessory

may grab the surface and pull the power tool out of your

control.

 Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into your

body.

 Regularly clean the power tool’s air vents. The motor’s

fan will draw the dust inside the housing and excessive

accumulation of powdered metal may cause electrical

hazards.

GENERAL SAFETY RULES

SERVICE

Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

WARNING!

To reduce the risk of injury, user must read instruction

manual.

When servicing a power tool, use only identical replace-

ment parts. Follow instructions in the Maintenance sec-

tion of this manual. Use of unauthorized parts or failure to

follow Maintenance instructions may create a risk of

shock or injury.

1 2 3 4 5 6 7 8 ... 35 36

Commentaires sur ces manuels

Pas de commentaire

Ryobi AG453K Manuel d'utilisateur Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Machines spéciales Ryobi AG453K