Ryobi EHT150V Manuel d'utilisateur télécharger pdf (Page 12)

English

FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR

 Insert the 3.2 mm collet.

 Replace and tighten the collet nut.

 Insert drive shaft into collet nut until the collar meets

the collet nut.

 Tighten the collet nut completely, keeping collar in

contact with the collet nut.

 Insert cup end of flex shaft onto tool head. Turn

clockwise to tighten.

To install accessories into the ﬂ ex shaft:

 Unplug the tool.

 Locate the hole behind the collet nut in the flex shaft

body.

 Turn the collet nut until the hole in the flex shaft body

aligns with the hole visible inside the flex shaft.

 Insert provided locking key into the aligned holes to

lock collet nut into place.

 Loosen the collet nut.

 Insert the shank of the accessory into the collet nut

until the shank bottoms out, then pull it out 1.6 mm

to allow for expansion when the accessory gets hot.

 With the key still in place, tighten the collet nut with the

provided wrench until the accessory shank is gripped

by the collet. Avoid excessive tightening of the collet

nut.

 Remove the key.

To remove accessories from the ﬂ ex shaft:

 Unplug the tool.

 Locate the hole behind the collet nut in the flex shaft

body.

 Turn the collet nut until the hole in the flex shaft body

aligns with the hole visible inside the flex shaft.

 Insert provided locking key into the aligned holes to

lock collet nut into place.

 With the key still in place, loosen the collet nut with the

provided wrench.

 Remove the accessory.

LIVE TOOL INDICATOR

This tool features a live tool indicator which illuminates as

soon as the tool is connected to the supply. This warns the

user that the tool is connected and will operate when the

switch is pressed.

MAINTENANCE

WARNING

When servicing, use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use.

Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING

Do not at any time let brake ﬂ uids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact

with plastic parts. They contain chemicals that can

damage, weaken or destroy plastic.

Do not abuse power tools. Abusive practices can damage

tool as well as workpiece.

WARNING

Do not attempt to modify this tool or create accessories

not recommended for use with this tool. Any such

alteration or modiﬁ cation is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

Electric tools used on ﬁ berglass material, wallboard,

spackling compounds, or plaster are subject to

accelerated wear and possible premature failure because

the ﬁ berglass chips and grindings are highly abrasive to

bearings, brushes, commutators, etc.

Consequently, we do not recommend using this tool for

extended work on these types of materials. However, if

you do work with any of these materials, it is extremely

important to clean the tool using compressed air.

LUBRICATION

All of the bearings in this tool are lubricated with a

sufﬁ cient amount of high grade lubricant for the life of

the unit under normal operating conditions. Therefore, no

further lubrication is required.

POWER SUPPLY CORD REPLACEMENT

If replacement of the power supply cord is necessary, this

must be done by an authorized service center in order to

avoid a safety hazard.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 254 255

Commentaires sur ces manuels

Pas de commentaire

Ryobi EHT150V Manuel d'utilisateur Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Ryobi EHT150V